Mitsubishi wd-57833 业主指南

The NetCommand system uses emitters connected to 

the 

IR EMITTER jack to control other devices such as 

DVD players, cable boxes, satellite receivers, and VCRs.

1.  Connect the plug end of the supplied IR emitter 

cable to the 

 jack on the 

TV back panel.

2.  Run the cable for each of the emitter ends under, 

alongside, or over each device to be controlled so 
that the emitter end is in front of the area where the 
remote control sensor is located.

3.  Position the emitter end with the emitter bulb facing 

the remote control sensor.  The bulb emits infrared 
light in a cone-shaped pattern.  Place the bulb far 
enough from the sensor to allow the cone pattern 
to reach the sensor.

The IR sensor is usually behind the plastic window 

of the front display panel.  It is sometimes visible 
with the aid of a flashlight and is normally a round 
or square cutout behind the plastic.
If you cannot see the sensor and the device’s 
Owner’s Guide does not specify the location, you 
can find it by following these steps using the 
device’s remote control:
a.  Hold the device’s remote about one-half inch 

from the front of the device.  Starting from one 
end of the display window plastic, press the 
POWER button.

b.  If the device does not respond, move the 

remote control one inch toward the center and 
try again.

c.  Repeat this until the device responds.
d.  Note this location and then start over from the 

other end of the display window plastic, repeat-
ing until the device responds again.

The remote control sensor is somewhere 

between these two positions.  This is usually 
enough accuracy for placement of the IR emit-
ters.
In some cases, the emitter works better facing 

downward from the top of the device.  Experi-

ment to find what works best.

4.  Secure the emitter ends in place using double-

sided tape.

5.  Place any unused ends behind the devices to 

prevent stray signals from reaching the IR sensors.

INPUT 1

INPUT 2

L

 

(

MONO)         R

AUDIO 

DIGITAL

AUDIO

OUT

HDMI

1

2

Y

Pb

Pr

AVR

AUDIO 

OUTPUT

S-VIDEO

VIDEO

3

L (MONO) - AUDIO - R

Y Pb Pr

 (480i/480p/720p/1080i)

VIDEO: 480i /480p /720p /1080i /1080p

AUDIO: PCM STEREO

PC: VGA / W-VGA / SVGA / W-SVGA /

       XGA / W-XGA / SXGA / 720p /1080p

  

IR EMITTER

NetCommand

R

PC/DVI

AUDIO

INPUT

COMPONENT 1

COMPONENT 2

ANT 2 / AUX

ANT 1 / MAIN

IR EMITTER

NetCommand

R

57#BDL1BOFM

% * ( * 5 " -

4 6 3 3 0 6 / %

4

$)

"73FDFJWFS

0UIFS"7%FWJDF

*OGSPOUPGB
TJOHMFBWFSBHF
TJ[FEEFWJDF

0OUPQPGBTJOHMF

UBMMEFWJDF

*OGSPOU TIBSFE
CZUXPBWFSBHF
TJ[FEEFWJDFT

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS

*OGSPOUPGBTJOHMF
BWFSBHFTJ[FEEFWJDF

0OUPQPGBTJOHMFUBMM
EFWJDF

*OGSPOU TIBSFECZUXP
BWFSBHFTJ[FEEFWJDFT

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS

*3TFOTPS