Roland GW-8 用户指南
46
System Settings
Settings that affect the entire operating environment of the
GW-8, such as tuning and MIDI message reception, are
referred to as “system settings.”
GW-8, such as tuning and MIDI message reception, are
referred to as “system settings.”
1.
Press [MENU].
2.
Use [
] [
] to select “System” then press [ENTER].
3.
Use [
] [
] to select a page, and use [
] [
] to
select the parameter that you want to edit.
For details, refer to “System Parameters” (below).
4.
Turn the VALUE dial to edit the value.
5.
When you’re finished making system settings, press [EXIT].
How to Make System Settings
([MENU])
([MENU])
System Parameters
SYSTEM GENERAL
Parameter
Value
Explanation
Master
Tune
Tune
415.3–
466.2Hz
466.2Hz
Adjusts the tuning of the entire GW-
8. The displayed value is the
frequency of the A4 key (middle A).
8. The displayed value is the
frequency of the A4 key (middle A).
Local
Switch*
Switch*
OFF, ON
System
Trans-
pose
Trans-
pose
-6–+5
Transposes the pitch of the GW-8
in semitone steps.
in semitone steps.
Bend
Mode
Mode
NORMAL
The pitch bend lever will operate in
the conventional way.
the conventional way.
CATCH+
LAST
LAST
If you play a note when the pitch
bend lever is already moved to one
side, the pitch will sound as though
the lever were in the center position.
When the lever passes through the
center position, it will once again
begin affecting the pitch. This will
apply only to the most recently
played note. You can use this to
simulate the double-bending
technique of an electric guitarist.
bend lever is already moved to one
side, the pitch will sound as though
the lever were in the center position.
When the lever passes through the
center position, it will once again
begin affecting the pitch. This will
apply only to the most recently
played note. You can use this to
simulate the double-bending
technique of an electric guitarist.
Screen
Saver
Time
Saver
Time
OFF, 5,
10–60
(min)
10–60
(min)
Set the time (minutes) until the
screen saver begins working. If this
is “OFF,” the screen saver will not
appear.
screen saver begins working. If this
is “OFF,” the screen saver will not
appear.
USB
Driver
Driver
VENDER,
GENERIC
GENERIC
SYSTEM PEDAL
Parameter
Value
Explanation
Pedal
Assign
Assign
Selects the function that will be controlled when
you press a separately available pedal
connected to the CONTROL PEDAL jack.
you press a separately available pedal
connected to the CONTROL PEDAL jack.
EXPRESSION
The pedal will function as an
Expression pedal.
Expression pedal.
CHORD
OFF
OFF
Chord detection in the Lower Part
area of the keyboard will be off
while you hold down the pedal,
allowing you to perform using the
entire keyboard. The setting will
return to its previous state when
you release the pedal.
area of the keyboard will be off
while you hold down the pedal,
allowing you to perform using the
entire keyboard. The setting will
return to its previous state when
you release the pedal.
CHORD
TOGGLE
TOGGLE
Chord detection in the Lower Part
area will turn off when you press
the pedal, allowing you to perform
using the entire keyboard. The
setting will return to its previous
state when you press the pedal
once again, so that chord detection
will be on for the Lower Part area.
area will turn off when you press
the pedal, allowing you to perform
using the entire keyboard. The
setting will return to its previous
state when you press the pedal
once again, so that chord detection
will be on for the Lower Part area.
SOSTENUTO
The pedal will function as a
Sostenuto pedal. When you press
the pedal, notes that are already
being held down will be sustained.
(This function can be used only for
the keyboard part.)
Sostenuto pedal. When you press
the pedal, notes that are already
being held down will be sustained.
(This function can be used only for
the keyboard part.)
SOFT
The pedal will function as a Soft
pedal. Notes you play while
holding down the pedal will have a
softer tone. (This function can be
used only for the keyboard part.)
pedal. Notes you play while
holding down the pedal will have a
softer tone. (This function can be
used only for the keyboard part.)
ROTARY
SLOW/
FAST
SLOW/
FAST
The pedal will switch the speed of
the rotary effect. This is valid only if
the ROTARY type is selected for
MFX (p. 42).
the rotary effect. This is valid only if
the ROTARY type is selected for
MFX (p. 42).
START/
STOP
STOP
The pedal will start/stop the
backing or song playback.
backing or song playback.
BASS
INVERSION
The pedal will switch the Bass Inversion
function on/off (p. 39).
function on/off (p. 39).
PUNCH
IN/OUT
IN/OUT
GW-8_e.book 46 ページ ２００８年７月３０日 水曜日 午後２時４分