Roland RD-700SX 业主指南
112
Effect/Parameter List
00: THRU
01: EQUALIZER
This is a four-band stereo equalizer (low, mid x 2, high).
02: SPECTRUM
This is a stereo spectrum. Spectrum is a type of filter which modifies
the timbre by boosting or cutting the level at specific frequencies.
the timbre by boosting or cutting the level at specific frequencies.
03: ISOLATOR
This is an equalizer which cuts the volume greatly, allowing you to
add a special effect to the sound by cutting the volume in varying
ranges.
add a special effect to the sound by cutting the volume in varying
ranges.
04: LOW BOOST
Boosts the volume of the lower range, creating powerful lows.
05: SUPER FILTR (SUPER FILTER)
This is a filter with an extremely sharp slope. The cutoff frequency can
be varied cyclically.
be varied cyclically.
Multi-Effects Parameter
Assignable Parameters
MFX Control
Low Gain, High Gain, Level
Parameter
Value
Description
Low Freq
200, 400 Hz
Frequency of the low range
Low Gain
-15– +15 dB
Gain of the low range
Mid1 Freq
200–8000 Hz
Frequency of the middle range 1
Mid1 Gain
-15– +15 dB
Gain of the middle range 1
Mid1 Q
0.5, 1.0, 2.0,
4.0, 8.0
4.0, 8.0
Width of the middle range 1
Set a higher value for Q to narrow the
range to be affected.
Set a higher value for Q to narrow the
range to be affected.
Mid2 Freq
200–8000 Hz
Frequency of the middle range 2
Mid2 Gain
-15– +15 dB
Gain of the middle range 2
Mid2 Q
0.5, 1.0, 2.0,
4.0, 8.0
4.0, 8.0
Width of the middle range 2
Set a higher value for Q to narrow the
range to be affected.
Set a higher value for Q to narrow the
range to be affected.
High Freq
2000, 4000,
8000 Hz
8000 Hz
Frequency of the high range
High Gain
-15– +15 dB
Gain of the high range
Level
0–127
Output Level
Assignable Parameters
MFX Control
Level
Parameter
Value
Description
Band1 (250Hz)
-15– +15 dB
Gain of each frequency band
Band2 (500Hz)
Band3 (1000Hz)
Band4 (1250Hz)
Band5 (2000Hz)
Band6 (3150Hz)
Band7 (4000Hz)
Band8 (8000Hz)
Q
Band3 (1000Hz)
Band4 (1250Hz)
Band5 (2000Hz)
Band6 (3150Hz)
Band7 (4000Hz)
Band8 (8000Hz)
Q
0.5, 1.0, 2.0,
4.0, 8.0
4.0, 8.0
Simultaneously adjusts the width of the
adjusted ranges for all the frequency
bands.
adjusted ranges for all the frequency
bands.
Level
0–127
Output Level
Assignable Parameters
MFX Control
Boost/Cut Low, Boost/Cut Mid, Boost/Cut High
Parameter
Value
Description
Boost/Cut Low -60– +4 dB
These boost and cut each of the High,
Middle, and Low frequency ranges.
At -60 dB, the sound becomes inaudible.
0 dB is equivalent to the input level of
the sound.
Middle, and Low frequency ranges.
At -60 dB, the sound becomes inaudible.
0 dB is equivalent to the input level of
the sound.
Boost/Cut Mid
Boost/Cut
High
Boost/Cut
High
APhase Low
Sw
Sw
OFF, ON
Turns the Anti-Phase function on and
off for the Low frequency ranges.
When turned on, the counter-channel of
stereo sound is inverted and added to
the signal.
off for the Low frequency ranges.
When turned on, the counter-channel of
stereo sound is inverted and added to
the signal.
APhase Low
Lev
Lev
0–127
Adjusts the level settings for the Low
frequency ranges.
Adjusting this level for certain
frequencies allows you to lend
emphasis to specific parts. (This is
effective only for stereo source.)
frequency ranges.
Adjusting this level for certain
frequencies allows you to lend
emphasis to specific parts. (This is
effective only for stereo source.)
APhase Mid Sw OFF, ON
Settings of the Anti-Phase function for
the Middle frequency ranges
The parameters are the same as for the
Low frequency ranges.
the Middle frequency ranges
The parameters are the same as for the
Low frequency ranges.
APhase Mid
Lev
Lev
0–127
Low Boost Sw
OFF, ON
Turns Low Booster on/off.
This emphasizes the bottom to create a
heavy bass sound.
This emphasizes the bottom to create a
heavy bass sound.
Low Boost
Level
Level
0–127
Increasing this value gives you a heavier
low end.
Depending on the Isolator and filter
settings this effect may be hard to
distinguish.
low end.
Depending on the Isolator and filter
settings this effect may be hard to
distinguish.
Level
0–127
Output Level
Assignable Parameters
MFX Control
Boost Gain, Boost Freq
Parameter
Value
Description
Boost Freq
50–125 Hz
Center frequency at which the lower
range will be boosted
range will be boosted
Boost Gain
0– +12 dB
Amount by which the lower range will
be boosted
be boosted
Boost Width
WIDE, MID,
NARROW
NARROW
Width of the lower range that will be
boosted
boosted
Low Gain
-15– +15 dB
Gain of the low frequency range
High Gain
-15– +15 dB
Gain of the high frequency range
Level
0–127
Output level
Assignable Parameters
MFX Control
Filter Cutoff, Filter Resonance, Rate, Depth
Parameter
Value
Description
Filter Type
LPF, BPF,
HPF,
NOTCH
HPF,
NOTCH
Filter type
Frequency range that will pass through
each filter
Frequency range that will pass through
each filter
LPF
: Frequencies below the cutoff
BPF
: Frequencies in the region of the
cutoff
HPF
: Frequencies above the cutoff
NOTCH
: Frequencies other than the
region of the cutoff
Filter Slope
-12, -24, -36
dB
dB
Amount of attenuation per octave
-36 dB
: Extremely steep
-24 dB
: Steep
-12 dB
: Gentle
Filter Cutoff
0–127
Cutoff frequency of the filter
Increasing this value will raise the cutoff
frequency.
Increasing this value will raise the cutoff
frequency.
Filter
Resonance
Resonance
0–127
Filter resonance level
Increasing this value will emphasize the
region near the cutoff frequency.
Increasing this value will emphasize the
region near the cutoff frequency.
Filter Gain
0– +12 dB
Amount of boost for the filter output
Parameter
Value
Description
RD-700SX_e.book 112 ページ 2007年9月12日 水曜日 午前11時10分