Roland RD-300SX 业主指南
41
Settings for Each Function ([EDIT])
1.
Press [EDIT].
The indicator lights, and the RD-300SX switches to Edit mode.
2.
Press [INC] or [DEC] to select “Tone,” then press [ENTER].
fig.disp.ton
3.
Referring to the following, press the TONE SELECT button
to which the parameter you want to change is assigned.
to which the parameter you want to change is assigned.
The parameter name appears in the display while the button is
held down. When the button is released, the value for the
parameter is shown in the display.
held down. When the button is released, the value for the
parameter is shown in the display.
When setting the LOWER zone, set [LOWER SELECT] to ON.
Only the indicators of buttons to which a parameter is assigned
blink.
blink.
4.
Press [INC] or [DEC] to set the value.
5.
Press [EDIT] to turn off the indicator and quit editing.
You can return to Step 2 by pressing [EXIT].
You can make changes in tones by adjusting the settings of the
following five elements.
following five elements.
Cutoff:
Adjusts how much the filter is opened.
Resonance:
This boosts the portions in the region around the
cutoff frequency, lending a particular quality to the
sound. Excessively high settings can produce
oscillation, causing the sound to distort.
cutoff frequency, lending a particular quality to the
sound. Excessively high settings can produce
oscillation, causing the sound to distort.
Attack Time:
The time it takes after the key is pressed for a sound
to reach full volume.
to reach full volume.
Decay Time:
The time it is to take following the attack for the
volume to decrease.
volume to decrease.
Release Time:
The time it takes after the key is released for a sound
to become inaudible.
to become inaudible.
Making abrupt changes in the settings values may cause the
sound to become distorted or overly loud. Carefully monitor
volume levels while making the settings.
sound to become distorted or overly loud. Carefully monitor
volume levels while making the settings.
The effect may not be apparent with some tones, even when the
value is changed.
value is changed.
This sets the depth of the reverb effect for each tone.
When this value is set to “0,” no effect is applied even when
[REVERB] is pressed.
[REVERB] is pressed.
You can also make the setting by holding down [REVERB] and
adjusting the ZONE LEVEL slider.
adjusting the ZONE LEVEL slider.
Tone Settings
(Tone Parameter)
How to Make Settings
TONE
SELECT
button
SELECT
button
Indication
Parameter
PIANO
E.PIANO
ORGAN
STRINGS/
PAD
PAD
GUITAR/
BASS
BASS
BRASS/
WINDS
WINDS
VOICE/
SYNTH
SYNTH
RHY/GM2
Changing Tone Elements
(Cutoff/Resonance/Attack Time/
Decay Time/Release Time)
Parameter
Value
Description
Cutoff
-64–0– +63
Higher values brighten the sound;
lower values make the sound seem
darker.
lower values make the sound seem
darker.
Resonance
-64–0– +63
Higher value makes the special
quality of the sound stronger;
lower value reduce these charac-
teristics.
quality of the sound stronger;
lower value reduce these charac-
teristics.
Attack Time
-64–0– +63
Higher values produce a milder at-
tack; lower values produce a sharper
attack.
tack; lower values produce a sharper
attack.
Decay Time
-64–0– +63
The time it takes for the volume to
fall increases as the value is
raised; lowering the value de-
creases the decay time.
fall increases as the value is
raised; lowering the value de-
creases the decay time.
Release Time
-64–0– +63
Higher values produce longer decay;
set lower values for a clear-cut sound.
set lower values for a clear-cut sound.
Setting the Amount of Reverb Applied
to Each Tone
(Reverb Send Level)
Value
0–127
RD-300SX_e.book 41 ページ 2005年12月26日 月曜日 午後8時37分