LXE hx3 参考指南
Batteries
53
E-EQ-HX3RG-C
HX3 Reference Guide
Low Battery Warning
It is recommended that the main battery pack be removed and replaced when its energy depletes.
When the main battery Low Battery Warning appears (the Status LED remains a steady red) place
the HX3 in suspend by pressing the Power key before changing the battery.
When the main battery Low Battery Warning appears (the Status LED remains a steady red) place
the HX3 in suspend by pressing the Power key before changing the battery.
Note:
Once you receive the main battery Low Battery Warning, you have approximately 5
minutes to perform an orderly shutdown and replace the main battery pack before the
device powers off. The Low Battery Warning will transition the mobile device to Suspend
before the device powers off.
minutes to perform an orderly shutdown and replace the main battery pack before the
device powers off. The Low Battery Warning will transition the mobile device to Suspend
before the device powers off.
Main Battery Pack
The main battery pack has a rugged plastic enclosure that is designed to withstand the ordinary
rigors of an industrial environment. Exercise care when transporting the battery pack making sure
it does not come in contact with excessive heat or any power source other than the HX2 Multi-
Charger, HX2 Cradle or the HX3 unit.
rigors of an industrial environment. Exercise care when transporting the battery pack making sure
it does not come in contact with excessive heat or any power source other than the HX2 Multi-
Charger, HX2 Cradle or the HX3 unit.
Whenever possible, protect the battery charging terminals (five small round circles) by keeping
them covered by the battery sleeve fabric. The battery pack is resistant to impact damage.
them covered by the battery sleeve fabric. The battery pack is resistant to impact damage.
Under normal conditions a properly tethered Standard battery should last a minimum of
approximately eight hours before requiring a recharge, the Extended battery a minimum of
approximately 16 hours.
approximately eight hours before requiring a recharge, the Extended battery a minimum of
approximately 16 hours.
Battery Hotswapping
Important:
When the backup battery power is Low or Very Low (
| Settings | Control Panel |
Power | Battery tab) dock the HX3 in a powered docking cradle before replacing the battery
pack.
pack.
Viewing the backup battery status requires an ActiveSync connection and
LXEConnect. Please see “ActiveSync and the HX3” in Chapter 3 System
Configuration for details on establishing this connection.
LXEConnect. Please see “ActiveSync and the HX3” in Chapter 3 System
Configuration for details on establishing this connection.
When the main battery power level is low, the HX3 will signal the user with the low battery
warning indicator (the Status LED remains a steady red) that continues until the main battery is
replaced, the battery completely depletes, or external power is applied to the HX3 using a
powered cradle.
warning indicator (the Status LED remains a steady red) that continues until the main battery is
replaced, the battery completely depletes, or external power is applied to the HX3 using a
powered cradle.
You can replace the main battery by first placing the device in Suspend Mode then removing the
discharged main battery and tethering a charged main battery within a five minute time limit (or
before the backup battery depletes).
discharged main battery and tethering a charged main battery within a five minute time limit (or
before the backup battery depletes).
When the main battery is disconnected the device enters Critical Suspend state, the HX3 remains
in Suspend mode and the backup battery continues to power the unit for at least five minutes.
Though data is retained, the HX3 cannot be used until a charged main battery pack is connected.
After tethering the full battery, press the Power key.
in Suspend mode and the backup battery continues to power the unit for at least five minutes.
Though data is retained, the HX3 cannot be used until a charged main battery pack is connected.
After tethering the full battery, press the Power key.
Full operational recovery from Suspend can take several seconds while the wireless client
connects to the network, authorization for Voxware-enabled applications complete, Wavelink
Avalanche management of the HX3 startup completes, and Bluetooth relationships establish or re-
establish.
connects to the network, authorization for Voxware-enabled applications complete, Wavelink
Avalanche management of the HX3 startup completes, and Bluetooth relationships establish or re-
establish.
If the backup battery depletes before a fully charged main battery can be inserted, the HX3 will
turn Off.
turn Off.