Whirlpool GU3100XTV 用户手册

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.

Check that all parts are included. See separate parts list for 
accessories available for your dishwasher.

IMPORTANT: Observe all governing codes and ordinances. 
Failure to meet codes and ordinances could lead to fire or 
electrical shock.
Proper installation is your responsibility.

■

Contact a qualified installer to ensure that the dishwasher is 
installed to meet all electrical and plumbing national and local 
codes and ordinances.

■

Install the dishwasher as specified in these instructions.

■

Have everything you need to properly install dishwasher.

■

Shelter dishwasher and water lines leading to dishwasher 
against freezing. Damage from freezing is not covered by the 
warranty.

■

This dishwasher is manufactured for indoor use only.

■

Do not run drain lines, water lines or electrical wiring where 
they can interfere with or contact the dishwasher motor or 
legs.

■

The location where the dishwasher will be installed must 
provide clearance between motor and flooring. Motor should 
not touch the floor.

■

Do not install dishwasher over carpeted flooring.

Check location where the dishwasher will be installed. the location 
must provide:

■

Easy access to water, electricity and drain.

■

Convenient access for loading and unloading dishes. Corner 
locations require 2" (5.1 cm) minimum clearance between the 
side of the dishwasher door and the wall or cabinet.

■

A minimum of 25

⁵⁄₈" (65.1 cm) is required in front of the 

dishwasher to allow the door to open fully.

■

Square opening for proper orientation.

■

Cabinet front perpendicular to floor.

■

Level floor. If the floor at the front of the dishwasher is not level 
with the rear of the opening, shims may be needed to level the 
dishwasher.

NOTE: To avoid shifting during dishwasher operation, shims 
must be securely attached attached to the floor.

If the dishwasher will be left unused for a period of time or in a 
location where it may be subject to freezing, have it winterized by 
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area 
shown in the “Cutout dimensions” section.
Helpful Tip: If the floor in the dishwasher opening is uneven 
(example: tile flooring only partway into opening) you will need to 
be accurate when measuring the dimensions and in leveling the 
dishwasher. 

■

Phillips screwdriver

■

Flat-blade screwdriver

■

⁵⁄₁₆" and ¼" nut drivers 

■

Measuring tape or ruler

■

¹⁄₂", ³⁄₄" and 1½" (1.3 mm, 

1.9 mm and 3.8 cm) hole 
saw bits

■

Twist-on wire connectors 
(proper size to connect 
household wiring to
16-gauge wiring in 
dishwasher) (2)

■

6" (15.2 cm) adjustable 
wrench

■

Small tubing cutter

■

Level

■

Cordless drill

■

¹⁄₈" drill bit

■

Flashlight

■

Shallow pan

■

Wood block

■

Bath towel

■

90º elbow with 

³⁄₈" N.P.T. 

external threads on one 
end

NOTE: The other end 
must fit the water supply 
line.

■

Thread seal tape

■

3 UL listed wire nuts

■

Copper tubing 
(

³⁄₈" recommended)

■

1

¹⁄₂" to 2" (3.8 cm to 

5.1 cm) screw-type clamp

■

Clamp connector to fit 

⁷⁄₈" 

(22.2 cm) diameter hole

■

1

¹⁄₂" to 2" (3.8 cm to 

5.1 cm) screw-type clamp 
if connecting to waste-tee

⁵⁄₈

A

B

⁵⁄₈