Whirlpool GU3100XTV 用户手册

Contact a qualified electrician.
Ensure that the electrical installation is adequate and in 
conformance with all national and local codes and ordinances.

Requirements:

■

120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical 
supply

■

Copper wire only, 2 wire with ground

Recommended:

■

Time-delay fuse or circuit breaker

■

Separate circuit

■

Use flexible, armored or nonmetalic sheathed, copper wire 
with grounding wire that meets the wiring requirements for 
your home and local codes and ordinances.

■

Use strain relief method provided with house wiring junction 
box or install a UL-listed/CSA-certified clamp connector to the 
house wiring junction box. If using conduit, use a 
UL-listed/CSA-certified conduit connector.

Use Power Supply Cord Kit (Part Number 4317824) marked for 
use with dishwashers. Kit contents include:

■

Voltex, Inc., UL listed 16 gauge 3-wire power supply cord with 
3 prong grounding plug

■

Neer C-500 

⁷⁄₈" strain relief

■

3 wire connectors

■

Part No. 302797 grommet

Follow the kit instructions for installing the power supply cord.
NOTE: Power supply cord must plug into a mating three prong, 
grounded outlet, located in the cabinet next to the dishwasher 
opening. Outlet must meet all local codes and ordinances.
IMPORTANT: If you plan to install a garbage disposal, an 
additional separate 120-volt, 60 Hz, AC-only, 15- or 20-amp fused 
electrical supply is required.

■

A hot water line with 20-120 psi (138-862 kPa) water pressure.

■

120°F (49°C) water temperature at dishwasher.

■

³⁄₈" O.D. copper tubing with compression fitting or flexible 

braided water supply line

.

NOTE: ½" minimum plastic tubing is not recommended.

■

90º elbow with 

³⁄₈" N.P.T. external pipe threads on one end.

IMPORTANT: Do not solder within 6" (15.2 cm) from water inlet 
valve.

■

Use the new drain hose supplied with your dishwasher. 
NOTE: If a longer drain hose is required:

■

Use a new drain hose with maximum length of 10 ft (3 m) 
that meets all current AHAM/IAPMO test standards

■

Use a new drain hose that is resistant to heat and 
detergent

■

Use a new drain hose that fits the 1" (2.5 cm) drain 
connector on the dishwasher.

■

Connect drain hose to waste tee or disposal inlet above drain 
trap in house plumbing.

■

Connect drain hose to house plumbing 20" (50.8 cm) 
minimum above the floor. 

NOTE: It is recommended that the drain hose either be looped up 
and securely fastened to the underside of the counter, or be 
connected to an air gap.

■

Use a drain air gap if the drain hose is connected to house 
plumbing lower than 18" (45.7 cm) above the subfloor or floor.

■

Use ½" (1.3 cm) minimum I.D. drain line fittings.

NOTE: Do not connect drain lines from other devices to the 
dishwasher drain hose.

■  

The dishwasher must be grounded. In the event of a 
malfunction or breakdown, grounding will reduce the 
risk of electric shock by providing a path of least 
resistance for electric current. The dishwasher is 
equipped with a cord having an equipment-grounding 
conductor and a grounding plug. The plug must be 
plugged into an appropriate outlet that is installed and 
grounded in accordance with all local codes and 
ordinances.

WARNING: 

Improper connection of the 

equipment-grounding conductor can result in a risk of 
electric shock. Check with a qualified electrician or 
service representative if you are in doubt whether the 
dishwasher is properly grounded. Do not modify the 
plug provided with the dishwasher; if it will not fit the 
outlet, have a proper outlet installed by a qualified 
electrician.

■  

The dishwasher must be connected to a grounded 
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit 
conductors and connected to the equipment-
grounding terminal or lead on the dishwasher.