ICOM IC-7000 说明手册
40
4
RECEIVE AND TRANSMIT
4
D
Convenient functions for transmit
• Transmit quality monitor
(p. 87)
➥ Push
[AF(
SET
)]
, then
[F-4
O
OT
TH
H
]
to enter the mis-
cellaneous (others) set mode. Select an item with
[F-1
≤
≤
]
/
[F-2
≥
≥
]
, then rotate
[DIAL]
to turn the
monitor function ON and OFF.
• VOX (voice operated transmit)
(p. 83)
➥ While “M
M--3
3” is selected, push
[F-1
V
VO
OX
X
]
to turn
the VOX function ON and OFF.
• “
” appears when the VOX function is set to ON.
➥ While “M
M--3
3” is selected, push and hold
[F-1
V
VO
OX
X
]
for 1 sec. to enter the VOX set mode.
• Push
[F-1
≤
≤
]
/
[F-2
≥
≥
]
to select an item.
• Rotate
[DIAL]
to set the value/conditions.
• Speech compressor
(p. 87)
➥ While “M
M--3
3” is selected, push
[F-2
C
CO
OM
M
]
to turn
the speech compressor ON and OFF.
• “
” appears when the speech compressor is set to
ON.
➥ While “M
M--3
3” is selected, push and hold
[F-2
C
CO
OM
M
]
for 1 sec. to enter the compression level set
mode.
mode.
• Rotate
[DIAL]
to adjust the compression level.
• Transmit filter width
(p. 84)
➥ While “M
M--3
3” is selected, push
[F-4
T
TB
BW
W
]
momen-
tarily to display the selected transmit filter width.
➥ While “M
M--3
3” is selected, push and hold
[F-4
T
TB
BW
W
]
for 1 sec. to select the transmit filter width from
narrow, middle and width.
narrow, middle and width.
• The transmit filter width window appears for showing
the selected transmit filter width each time
[F-4
T
TB
BW
W
]
is pushed.
• Push and hold
[MENU/GRP]
for 1 sec. once or twice
to select the menu group M
M.
• Push
[MENU/GRP]
momentarily one or more times
to select the menu M
M--3
3.
D
D
About 5 MHz band operation (USA version only)
Operation on the 5 MHz band is allowed on 5 discrete
frequencies and must adhere to the following:
• USB mode
• Maximum of 50 watts ERP
frequencies and must adhere to the following:
• USB mode
• Maximum of 50 watts ERP
(Effective Radiated Power)
• 2.8 kHz bandwidth
It is the operator’s responsibility to set all controls so
that the transmission in this band meets the stringent
conditions under which we may use these frequencies.
that the transmission in this band meets the stringent
conditions under which we may use these frequencies.
NOTE:
We recommend that you store these fre-
quencies, mode and filter settings into the memory
channel for easy recall.
channel for easy recall.
*The channel center frequencies that are specified
by the FCC, show the center frequency of their
passband. However, the IC-7000 displays carrier
point frequency, so set 1.5 kHz below from FCC
channel center frequency.
passband. However, the IC-7000 displays carrier
point frequency, so set 1.5 kHz below from FCC
channel center frequency.
IC-7000 Display
FCC Channel
Frequency*
Center Frequency*
5.33050 MHz
5.33200 MHz
5.34650 MHz
5.34800 MHz
5.36650 MHz
5.36800 MHz
5.37150 MHz
5.37300 MHz
5.40350 MHz
5.40500 MHz
To assist you in operating the 5 MHz band correctly
within the rules specified by the FCC, transmission
is impossible on any 5 MHz band frequency other
than the 5 frequencies indicated in the table above.
within the rules specified by the FCC, transmission
is impossible on any 5 MHz band frequency other
than the 5 frequencies indicated in the table above.