Xerox Phaser 3140 用户指南

Management tools_ 47

Find solutions for problems by using the Troubleshooting Guide. 
Double click the Status Monitor icon on the Windows task bar.
Or, from the Start menu, select Programs or All Programs > your printer 

driver name > Troubleshooting Guide.

This program is for the network IP setting using the MAC address which is 

the hardware serial number of the network printer card or interface.
It is especially for the network administrator to set several network IPs at the 

same time. 

•

TCP/IPv6 is not supported by this program.

•

You can only use the SetIP program when your machine is 

connected to a network. 

The following procedure is based on the Windows XP operating system.

1. Make sure that the machine is connected to your computer and 

powered on.

2. Insert the supplied software CD into your CD-ROM drive.

•

The software CD should automatically run and an installation 

window appear.

•

If the installation window does not appear, click Start and then 

Run. Type X:\Setup.exe, replacing “X” with the letter which 

represents your drive. Click OK.

•

If you use Windows Vista, click Start > All programs > 

Accessories > Run.
Type X:\Setup.exe replacing “X” with the letter which represents 

your drive and click OK.

•

If the AutoPlay window appears in Windows Vista, click Run 

Setup.exe in Install or run program field, and click Continue in 

the User Account Control windows.

3. Click Install SetIP Utility(Optional).
4. Click Next > Next.
5. Click Finish.

In ready mode, press and hold the  (cancel button) for about 

7 

seconds. You can find your machine’s MAC address and IP address.

1. Print the machine’s network configuration report to find your 

machine’s MAC address. 

2. From the Windows Start menu, select All Programs > SetIP > 

SetIP.

3. Click to open the TCP/IP configuration window. 
4. Enter the network card’s MAC address, IP address, subnet mask, 

default gateway, and then click Apply. 

When you enter the MAC address, enter it without a colon(:).

5. The machine prints the network configuration report. Confirm all the 

settings are correct. 

6. Close the SetIP program. 

SetIP program should be automatically installed during the printer driver 

installation.

In ready mode, press and hold the  (cancel button) for about 

7 

seconds. You can find your machine’s MAC address and IP address.

If you want to change your network printer IP setting, follow the below 

instruction.

If you select Typical installation for a network printer during the 

printer driver installation, the SetIP program automatically runs 

after the installation. Go to step 4.

1. Print the machine’s network configuration report to find your 

machine’s MAC address. 

2. Open the Library folder > Printers > Xerox > your printer model 

name > SetIP.

3. Double click the SetIPApplet.html file. 
4. The certificate window appears, click Trust. 
5. Click to open the TCP/IP configuration window. 
6. Enter the network card’s MAC address, IP address, subnet mask, 

default gateway, and then click Apply. 

When you enter the MAC address, enter it without a colon(:).

7. The machine prints the network configuration report. Confirm all the 

settings are correct. 

8. Close the SetIP program. 

SetIP program should be automatically installed during the printer driver 

installation.

In ready mode, press and hold the  (cancel button) for about 

7 

seconds. You can find your machine’s MAC address and IP address.

1. Print the machine’s network configuration report to find your 

machine’s MAC address. 

2. Open the /opt/Xerox/mfp/share/utils/.
3. Double click the SetIPApplet.html file. 
4. Click to open the TCP/IP configuration window. 
5. Enter the network card’s MAC address, IP address, subnet mask, 

default gateway, and then click Apply. 

When you enter the MAC address, enter it without a colon(:).

6. The machine prints the network configuration report. Confirm all the 

settings are correct. 

7. Close the SetIP program.