Sony STR-DB900 用户手册
18
GB
Before receiving broadcasts, make sure you
have connected the supplied FM and AM
antennas to the receiver (page 7).
have connected the supplied FM and AM
antennas to the receiver (page 7).
Automatic tuning
If you do not know the frequency of the station
you want, you can let the receiver scan all
available stations in your area.
you want, you can let the receiver scan all
available stations in your area.
1
Press TUNER to select the FM or AM
band.
band.
Or rotate INPUT SELECTOR on the
receiver to select “TUNER FM” or
“TUNER AM”.
receiver to select “TUNER FM” or
“TUNER AM”.
2
Press TUNING MODE repeatedly to
select “AUTO T.”.
select “AUTO T.”.
3
Press TUNING + or TUNING –.
Press TUNING + to scan from a low
frequency to a high one; press TUNING –
to scan from a high frequency to a low one.
frequency to a high one; press TUNING –
to scan from a high frequency to a low one.
The receiver stops scanning whenever a
station is received.
station is received.
When the receiver reaches either end
of the band
of the band
Scanning is repeated in the same direction.
4
To continue scanning, press TUNING +
or TUNING – again.
or TUNING – again.
Manual tuning
You can tune in the station in 50 kHz steps for
the FM band and 9 kHz steps for the AM band.
the FM band and 9 kHz steps for the AM band.
1
Press TUNER to select the FM or AM
band.
band.
Or rotate INPUT SELECTOR on the
receiver to select “TUNER FM” or
“TUNER AM”.
receiver to select “TUNER FM” or
“TUNER AM”.
2
Press TUNING MODE repeatedly to
select “MANUAL T.”.
select “MANUAL T.”.
3
Press TUNING + or TUNING –
repeatedly to tune in the station you
want.
repeatedly to tune in the station you
want.
Press TUNING + to change the frequency
from low to high.
from low to high.
Press TUNING – to change the frequency
from high to low.
from high to low.
Tip
If “STEREO” flashes in the display and FM stereo
reception is poor, press FM MODE to improve the
sound. In this case, the sound switches to monaural
reception and you will be unable to enjoy the effects of
stereo sound, but the overall sound will be less
distorted.
reception is poor, press FM MODE to improve the
sound. In this case, the sound switches to monaural
reception and you will be unable to enjoy the effects of
stereo sound, but the overall sound will be less
distorted.
If the system is forced to go into monaural mode by
pressing FM MODE, “MONO” appears in the display.
pressing FM MODE, “MONO” appears in the display.
Note
If “STEREO” does not appear at all when an FM
broadcast is received normally, press FM MODE to
turn on the “STEREO” indication. If the FM reception
is weak, “STEREO” will not light up.
broadcast is received normally, press FM MODE to
turn on the “STEREO” indication. If the FM reception
is weak, “STEREO” will not light up.
Preset tuning
You can preset your favorite FM or AM stations
to the receiver. This enables you to tune in the
stations directly. Up to 30 FM or AM stations
can be preset, and the receiver will scan all of the
stations you have preset.
Before tuning in preset stations, be sure to preset
them using the steps in “Presetting radio
stations”.
to the receiver. This enables you to tune in the
stations directly. Up to 30 FM or AM stations
can be preset, and the receiver will scan all of the
stations you have preset.
Before tuning in preset stations, be sure to preset
them using the steps in “Presetting radio
stations”.
Presetting radio stations
1
Press TUNER to select FM or AM band.
Or rotate INPUT SELECTOR on the
receiver. The last received station is tuned
in.
receiver. The last received station is tuned
in.
2
Tune in the station that you want to
preset using Automatic tuning
(page 18) or Manual tuning (page 18).
preset using Automatic tuning
(page 18) or Manual tuning (page 18).
3
Press MEMORY.
“MEMORY” appears in the display for a
few seconds.
few seconds.
Note
If the ALT key lights up during the above procedure,
press ALT to turn it off (deactivate ALT).
press ALT to turn it off (deactivate ALT).
Receiving broadcasts