Sony STR-DH810 用户手册
39
GB
Pre
p
ar
ing the
ing the
R
eceive
r
When error codes appear
1
Check the problem of the error.
*
xxx
represent a speaker channel
F
Front
S
Surround
SB
Surround back
FH
Front high
Depending on the error code, the speaker
channel may not appears.
channel may not appears.
2
Perform Auto Calibration again.
Press AMP, then press
Press AMP, then press
. Press
V/v to
select “RETRY? YES”, then press
.
3
When you select “PHASE
INFO.”
INFO.”
You can check the phase of each speaker (in
phase/out of phase).
phase/out of phase).
1
Press
V/v repeatedly to select a
speaker you want to check.
2
Press
to
return to step 2 of
When you select “WARN
CHECK”
CHECK”
If a warning on the measurement result is
present, detailed information is displayed.
present, detailed information is displayed.
Display and explanation
E -
xxx
*
: 31
E -
xxx
*
: 32
None of the speakers were detected. Make sure
that the optimizer microphone is connected
properly and perform the measurement again. If
the optimizer microphone is connected properly
but the error code appears, the optimizer
microphone cable may be damaged or
improperly connected.
that the optimizer microphone is connected
properly and perform the measurement again. If
the optimizer microphone is connected properly
but the error code appears, the optimizer
microphone cable may be damaged or
improperly connected.
E -
xxx
*
: 33
• None of the front speakers are connected or
only one front speaker is connected.
• The optimizer microphone is not connected.
• Either the left or right surround speakers is not
• Either the left or right surround speakers is not
connected.
• Surround back speakers or front high speakers
are connected even though surround speakers
are not connected. Connect the surround
speaker(s) to the SPEAKERS SURROUND
terminals.
are not connected. Connect the surround
speaker(s) to the SPEAKERS SURROUND
terminals.
The surround back speaker is connected only
to the SPEAKERS SURROUND BACK/
FRONT HIGH/BI-AMP/FRONT B R
terminals. When you connect only one
surround back speaker, connect it to the
SPEAKERS SURROUND BACK/FRONT
HIGH/BI-AMP/FRONT B L terminals.
to the SPEAKERS SURROUND BACK/
FRONT HIGH/BI-AMP/FRONT B R
terminals. When you connect only one
surround back speaker, connect it to the
SPEAKERS SURROUND BACK/FRONT
HIGH/BI-AMP/FRONT B L terminals.
• Either the front left high or front right high
speaker is not connected.
Checking the measurement
results
results
Display and explanation
xxx
*
: IN
The speaker is in phase.
xxx
*
: OUT
The speaker is out of phase. The “+” and “–”
terminals of the speaker may be connected the
other way around. However, depending on the
speakers, “
terminals of the speaker may be connected the
other way around. However, depending on the
speakers, “
xxx
: OUT” appears on the
display even though the speakers are connected
properly. This is because of the speakers’
specifications. In this case, you can continue to
use the receiver.
properly. This is because of the speakers’
specifications. In this case, you can continue to
use the receiver.
Display and explanation
W -
xxx
*
: 40
The measurement has completed. However, the
noise level is high. You may be able to perform the
measurement properly if you try it again, even
though the measurement cannot be performed in all
environments. Try to perform the measurement in a
quiet environment.
noise level is high. You may be able to perform the
measurement properly if you try it again, even
though the measurement cannot be performed in all
environments. Try to perform the measurement in a
quiet environment.
W -
xxx
*
: 41
The sound input from the optimizer microphone is
outside the acceptable range. It is louder than the
loudest sound that can be measured. Try to perform
the measurement when the environment is quiet
enough to allow proper measurement.
outside the acceptable range. It is louder than the
loudest sound that can be measured. Try to perform
the measurement when the environment is quiet
enough to allow proper measurement.
continued