Sony STR-DH710 用户手册
39
GB
Pre
p
ar
ing the
ing the
R
eceive
r
You can use the AUTO CAL menu to make
various adjustments for Auto Calibration
settings and to name the position.
Select “A. CAL” in the amplifier menus. For
details on adjusting the parameters, see “Using
the setting menu” (page 71) and “Overview of
the menus” (page 72).
various adjustments for Auto Calibration
settings and to name the position.
Select “A. CAL” in the amplifier menus. For
details on adjusting the parameters, see “Using
the setting menu” (page 71) and “Overview of
the menus” (page 72).
x START
x CAL TYPE*
Lets you select the Auto Calibration type for
each seating position. For details, see step 4 of
“3: Confirming/saving the measurement
results” (page 36).
each seating position. For details, see step 4 of
“3: Confirming/saving the measurement
results” (page 36).
* You can select this parameter only when you have
performed the Auto Calibration and saved the
settings.
settings.
x POSITION
You can register three patterns as position 1, 2,
3, depending on the seating positions, listening
environment, and measurement conditions.
If you do not select the position number, the
Auto Calibration result will automatically save
as POS 1 (initial setting).
3, depending on the seating positions, listening
environment, and measurement conditions.
If you do not select the position number, the
Auto Calibration result will automatically save
as POS 1 (initial setting).
To register more than one set of
settings for the listening
environment
settings for the listening
environment
You can select the seating position you want
and register the measurement results of the
Auto Calibration for that seating position.
and register the measurement results of the
Auto Calibration for that seating position.
1
Press AMP MENU.
2
Press
V/v repeatedly to select
“A. CAL”, then press
or
b.
3
Press
V/v repeatedly to select
“POSITION”, then press
or
b.
4
Press
V/v repeatedly to select the
position (POS 1, 2, 3) for which you
want to register the measurement
results, then press
want to register the measurement
results, then press
.
5
Press
V/v repeatedly to select
“START”, then press
to perform
Auto Calibration.
For details, see “2: Performing Auto
Calibration” (page 35).
The measurement results is registered as
the position you selected in step 4.
For details, see “2: Performing Auto
Calibration” (page 35).
The measurement results is registered as
the position you selected in step 4.
6
Repeat steps 1 to 5 to register another
seating position.
seating position.
To select the registered seating
position
position
1
Press AMP MENU.
2
Press
V/v repeatedly to select
“A. CAL”, then press
or
b.
3
Press
V/v repeatedly to select
“POSITION”, then press
or
b.
4
Press
V/v repeatedly to select position
(POS 1, 2, 3) you want, then press
.
The registered seating position is selected.
To exit the menu
Press AMP MENU.
x NAME IN (Naming position)
You can rename the position name.
1
Select the position (POS 1, 2, 3) for
which you want to name.
which you want to name.
2
Press
V/v repeatedly to select “NAME
IN”, then press
or
b.
The cursor flashes and you can select a
character.
character.
3
Press
V/v to select a character, then
press
B/b to move the cursor to the
next position.
If you made a mistake
Press
Press
B/b until the character you want to
change flashes, then press
V/v to select the
correct character.
AUTO CAL menu
continued