Panasonic sa-ht1000 用户手册

RQT7061

Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do 
not solve the problem:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail consumerproducts@panasonic.com, 
or the website (http://www.panasonic.com).
In Canada, contact the Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, or visit the website (www.panasonic.ca), 
or an authorized Servicentre closest to you.

Picture
≥When progressive output is on, refer also to “Progressive video” below.

≥Insert the AC power supply cord and system cable securely.

≥This is a power saving feature. You can turn it off if you would prefer (Set Up—Off Timer—Off). 

Press [

Í POWER] to turn the unit on.

≥One of the unit’s safety devices may have activated. Press [Í POWER] to turn the unit on.

≥Some operations may be prohibited by the disc.
≥The unit is hot (“U14” appears on the display). Wait for “U14” to disappear.
≥One of the unit’s safety devices may have activated.

Reset the unit as follows:
1 Press  [

Í POWER] to switch the unit to standby.

If the unit doesn’t switch to standby, press and hold [

Í POWER] for about 10 seconds. 

The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.

2 Press  [

Í POWER] to turn the unit on.

≥The selector has been set to “FM” or “AM”. Press [DVD] to select “DVD/CD” as the source.

≥[HOME THEATER, TV] is not switched to “HOME THEATER”. Switch to “HOME THEATER” 

when operating this unit.

≥The remote control and main unit are using different codes. Change the code on the remote 

control.

≥The batteries are depleted. Replace them with new ones.
≥Point the remote control at the remote control sensor on the main unit.
≥Remove obstacles from between the remote control and main unit.

≥Change manufacturer code. Some televisions cannot be operated even if you change the 

code.

≥[HOME THEATER, TV] is not switched to “TV”. Switch to “TV” when selecting the receiving 

channel for the television. 

≥Make sure that the television is connected to the VIDEO OUT terminal, S-VIDEO OUT 

terminal or COMPONENT VIDEO OUT terminals on this unit.

≥Make sure that the television’s input setting (e.g., VIDEO 1) is correct.
≥You have set “TV Type” to “Aspect 4:3 & 480P” or “Aspect 16:9 & 480P”  in the TV Screen 

menus, but the television isn’t compatible with progressive signals. Press and hold [

∫] and 

[TIME SLIP] on the unit at the same time for about 5 seconds. The setting will change to 
interlace.

≥This can occur because the signals are being divided between the unit and the television. 

It can be solved by using a signal booster, available from audio-visual suppliers. Consult your 
dealer if reception does not improve.

≥Check the settings on your television.
≥Check the settings for “TV Type”, “4:3 TV Settings for DVD-Video” or “4:3 TV Settings for 

DVD-RAM” in the TV Screen menu.

≥Go to the Display menu and select “Automatic” for “Status Messages”. 
≥Press [STATUS] to show the on-screen messages constantly. 

≥Go to the Display menu and select “On” for “Blue Background”.

≥Change the settings for “3D NR”, “Block NR”, and “Mosquito NR” to “0” or turn “MPEG-DNR” 

off if it is on.

≥Play may stop where two play lists join, but this is not a malfunction.

≥Set “Progressive” to “OFF”. This problem is caused by the editing method or material used on 

DVD-Video, but should be corrected if you use interlace output.

≥The effect is less perceivable with some types of video.

7061en.book  48 ページ  ２００３年７月１日　火曜日　午前１１時４４分