Cannondale marzucci fork 用户手册
22
F
ASE
7
Avvitare a mano il tappo (1) sull’estremità dell’asta
ammortizzatore.
Comprimere la molla per rendere accessibile il controdado
(12).
Utilizzando le chiavi dello smontaggio bloccare il tappo
(1) sull’asta ammortizzatore.
Serrare poi il controdado (12) contro il tappo (1).
ammortizzatore.
Comprimere la molla per rendere accessibile il controdado
(12).
Utilizzando le chiavi dello smontaggio bloccare il tappo
(1) sull’asta ammortizzatore.
Serrare poi il controdado (12) contro il tappo (1).
F
ASE
8
Lubrificare la guarnizione OR (2) sul tappo (1).
Sollevare il portastelo (6) e imboccarlo sul tappo (1)
facendo attenzione a non rovinare la guarnizione OR (2).
Serrare il tappo (1) sul portastelo (6).
Sollevare il portastelo (6) e imboccarlo sul tappo (1)
facendo attenzione a non rovinare la guarnizione OR (2).
Serrare il tappo (1) sul portastelo (6).
6.4- S
OSTITUZIONE
ANELLI
DI
TENUTA
N
OTA
:
Questa operazione non è possibile con steli montati
sul motociclo.
Ricambi necessari: N
Ricambi necessari: N
°
2 anelli di tenuta e N
°
2 raschiapolvere
nuovi.
S
MONTAGGIO
Eseguire le operazioni dalla F
ASE
1 alla F
ASE
4, riportate
al paragrafo 6.3.
F
ASE
9
Rimuovere con l’utilizzo di un piccolo cacciavite il
raschiapolvere (11) dalla sommità del portastelo (6).
raschiapolvere (11) dalla sommità del portastelo (6).
F
ASE
10
Con lo stesso cacciavite, sfilare l’anello di fermo (10).
F
ASE
11
Sfilare il portastelo (6) dal tubo portante (28). Per
separare i due elementi è necessario tirarli energicamente.
Con questa operazione verranno rimossi dal portastelo
l’anello di tenuta (9), lo scodellino (8) e la boccola di
guida (7).
separare i due elementi è necessario tirarli energicamente.
Con questa operazione verranno rimossi dal portastelo
l’anello di tenuta (9), lo scodellino (8) e la boccola di
guida (7).
F
ASE
12
Rimuovere la boccola di guida (27) dal tubo portante
facendo leva con l’estremità di un cacciavite piatto inserito
nella fessura della boccola.
Rimuovere poi dal tubo portante la boccola di guida (7),
lo scodellino (8), l’anello di tenuta (9), l’anello di fermo
(10) e il raschiapolvere (11).
facendo leva con l’estremità di un cacciavite piatto inserito
nella fessura della boccola.
Rimuovere poi dal tubo portante la boccola di guida (7),
lo scodellino (8), l’anello di tenuta (9), l’anello di fermo
(10) e il raschiapolvere (11).
S
TEP
7
Screw the plug (1) on the damper rod by hand.
Compress the spring so that the check nut (12) can be
reached.
Keep firmly the plug (1) on the damper rod with the
wrenches previously used for disassembling the fork
Tighten the check nut (12) on the plug (1).
Compress the spring so that the check nut (12) can be
reached.
Keep firmly the plug (1) on the damper rod with the
wrenches previously used for disassembling the fork
Tighten the check nut (12) on the plug (1).
S
TEP
8
Lubricate the OR (2) on the plug (1).
Lift the slider (6) and insert it into the plug (1). Do not
damage the OR (2).
Tighten the plug (1) on the slider (6).
Lift the slider (6) and insert it into the plug (1). Do not
damage the OR (2).
Tighten the plug (1) on the slider (6).
6.4- O
IL
SEAL
CHANGE
N
OTE
:
To change the oil seals, the fork legs must be
disassembled.
Seals Required: no. 2 new oil seals and no. 2 new dust
seals.
Seals Required: no. 2 new oil seals and no. 2 new dust
seals.
D
ISASSEMBLY
Follow the instructions from S
TEP
1 to S
TEP
4, as indi-
cated in the above paragraph.
S
TEP
9
Remove the dust seal (11) from the slider top (6) with a
small screwdriver.
small screwdriver.
S
TEP
10
Use the same screwdriver and remove the stop ring (10).
S
TEP
11
Pull out the slider (6) from the stanchion tube (28). Pull
vigorously to pull the two parts apart. In this way, oil seal
(9), cup (8) and pilot bushing (7) will be removed from
the slider.
vigorously to pull the two parts apart. In this way, oil seal
(9), cup (8) and pilot bushing (7) will be removed from
the slider.
S
TEP
12
Remove the pilot bushing (27) from the stanchion with a
flat screwdriver inserted in the bushing slot.
Then, remove pilot bushing (7), cup (8), oil seal (9), stop
ring (10) and dust seal (11) from the stanchion.
flat screwdriver inserted in the bushing slot.
Then, remove pilot bushing (7), cup (8), oil seal (9), stop
ring (10) and dust seal (11) from the stanchion.