bobcat 2200d 用户手册
Bobcat 2200 Diesel Vehicle
Operation & Maintenance Manual
Operation & Maintenance Manual
32
GEARCASE LUBRICATION
NOTE: Dispose of used oil according to the
environmental laws and regulations for your
area.
area.
Lubrication Level Check for Front Differential,
Transmission, and Rear Differential
Transmission, and Rear Differential
Each gearcase component is equipped with two oil port
plugs (1 and 2) [Figure 22, Figure 23, or Figure 24].
When the vehicle is on a level surface, use the level
indicator hole (upper plug) (1) as a lubricant level
indicator. Lubricant level should be even with the bottom
of level indicator hole (1).
plugs (1 and 2) [Figure 22, Figure 23, or Figure 24].
When the vehicle is on a level surface, use the level
indicator hole (upper plug) (1) as a lubricant level
indicator. Lubricant level should be even with the bottom
of level indicator hole (1).
Lubrication Change for Front Differential,
Transmission, and Rear Differential
Transmission, and Rear Differential
Use the lower plug (2) for drainage [Figure 22,
Figure 23, or Figure 24]. Remove both plugs to allow
the lubricant to drain faster. See preceding NOTE.
Figure 23, or Figure 24]. Remove both plugs to allow
the lubricant to drain faster. See preceding NOTE.
Front differential:
Clean and install the drain plug (2) and washer before
filling the front differential with new lubricant [Figure 22].
Tighten the drain plug to 12 Nm. Use a funnel when filling
the gearcase through the lubricant level indicator
hole (1). See PERIODIC LUBRICATION SCHEDULE on
page 27. Tighten the level indicator plug to 14 Nm.
filling the front differential with new lubricant [Figure 22].
Tighten the drain plug to 12 Nm. Use a funnel when filling
the gearcase through the lubricant level indicator
hole (1). See PERIODIC LUBRICATION SCHEDULE on
page 27. Tighten the level indicator plug to 14 Nm.
Transmission:
Clean and install the drain plug (2) before filling the
transmission with new lubricant [Figure 23]. Tighten the
drain plug to 11 Nm. Remove the fill plug on the top of the
transmission case and use a funnel when filling with
lubricant. See PERIODIC LUBRICATION SCHEDULE on
page 27. Apply Loctite 567 to the threads of the fill plug
and tighten to 28 Nm.
transmission with new lubricant [Figure 23]. Tighten the
drain plug to 11 Nm. Remove the fill plug on the top of the
transmission case and use a funnel when filling with
lubricant. See PERIODIC LUBRICATION SCHEDULE on
page 27. Apply Loctite 567 to the threads of the fill plug
and tighten to 28 Nm.
Check the level of lubricant at the level indicator plug (1).
Apply Loctite 567 to the threads of the level indicator plug
and tighten to 28 Nm.
Apply Loctite 567 to the threads of the level indicator plug
and tighten to 28 Nm.
Figure 22
Front Differential Lubrication Level
Figure 23
Transmission Lubrication Level
Clean and install the drain plug (2) and washer before
filling the rear differential with new lubricant [Figure 24].
Tighten the drain plug to 10,8 Nm. Use a funnel when
filling the differential through the lubricant level indicator
hole (1). See PERIODIC LUBRICATION SCHEDULE on
page 27. Apply Loctite 567 to the threads of the level
indicator plug and tighten to 28 Nm.
filling the rear differential with new lubricant [Figure 24].
Tighten the drain plug to 10,8 Nm. Use a funnel when
filling the differential through the lubricant level indicator
hole (1). See PERIODIC LUBRICATION SCHEDULE on
page 27. Apply Loctite 567 to the threads of the level
indicator plug and tighten to 28 Nm.
Figure 24 Rear Differential Lubrication Level
1
2
1
2
1
2