Graupner GmbH & Co. KG MC-20 用户手册
148 Detail program description - Phase assignment
Phase assignment
Setting up fl ight phases
Use the selection keys of the left or right touch pad to
scroll to the »Phase assignment« menu option in the
multi-function menu:
scroll to the »Phase assignment« menu option in the
multi-function menu:
Ser vo adjustment
Stick mode
Control adjust
Dual Rate / Expo
Channel 1 cur ve
Switch display
Base setup model
Model type
Control switch
Logical switch
Phase settings
Phase assignment
Ser vo adjustment
Stick mode
Control adjust
Dual Rate / Expo
Channel 1 cur ve
Switch display
Base setup model
Helicopter type
Control switch
Logical switch
Phase settings
Phase assignment
Open this menu option with a tap on the center
SET
key of the right touch pad.
P H A S E A S S I G N M E N T
prior
C
1 Nor mal
combi
A
B
D
E
F
Note:
A phase name appears to the right of the phase
number at the bottom right of the display only if you
have assigned the name beforehand on the »Phase
settings« menu.
A phase name appears to the right of the phase
number at the bottom right of the display only if you
have assigned the name beforehand on the »Phase
settings« menu.
In the »Phase settings« menu, described above
separately for fi xed-wing and helicopter models, you
separately for fi xed-wing and helicopter models, you
will have set up names for your phases. On this menu
– which is identical for both model types – you must
now specify the switches or switch combinations that
you want to use to trigger each phase. One exception
for helicopter menu: one of the two auto-rotation
switches must be set on the menu »Basic settings,
model«.
– which is identical for both model types – you must
now specify the switches or switch combinations that
you want to use to trigger each phase. One exception
for helicopter menu: one of the two auto-rotation
switches must be set on the menu »Basic settings,
model«.
Please note the following priorities:
If
•
no fl ight phase switches nor these names have
been assigned in this menu, the model is in fl ight
phase "1". Accordingly, by the time you start
programming fl ight phases, you should therefore
have already given this fl ight phase the phase
name "Normal".
Independent of the phases with allocated switch
phase "1". Accordingly, by the time you start
programming fl ight phases, you should therefore
have already given this fl ight phase the phase
name "Normal".
Independent of the phases with allocated switch
•
settings made in this menu, the autorotation phase
(only present for the "Helicopter" model type and
to be assigned a switch in the »Basic settings,
model« menu) always (!) takes precedence.
Accordingly, as soon as the auto-rotation switch
in question is activated, the following warning
appears:
(only present for the "Helicopter" model type and
to be assigned a switch in the »Basic settings,
model« menu) always (!) takes precedence.
Accordingly, as soon as the auto-rotation switch
in question is activated, the following warning
appears:
P H A S E A S S I G N M E N T
prior
C
1 Nor mal
Kombination
A
B
D
E
F
Autorot
Phase switch "A" is given priority over all
•
subsequent switch positions, from "B" to "F"
Phase switch "B" is given priority over all
Phase switch "B" is given priority over all
•
subsequent switch positions, from "C" to "F"
3-way switches should
3-way switches should
•
always be assigned from
the middle position.
Therefore use switch "A" and/or switch "B" only if you
wish to change from any other fl ight phase – apart
wish to change from any other fl ight phase – apart
from the helicopter's autorotation phase – directly into
the phase that is assigned to this switch.
the phase that is assigned to this switch.
Programming fl ight phase switches
Once you have confi gured your desired switch
position, "A" to "F", using the selection keys on the
left or right touch pad, a switch (whether a "normal"
switch or an expanded switch) is then assigned
as described in the section "Assigning transmitter
controls, switches and control switches" (page 56).
The order in which assignment is made is irrelevant:
you must ensure only that you assign what are,
for you, the "correct" switches. (In the helicopter
program, for example, you should also take care
to ensure you do not use this menu to re-assign
any auto-rotation switch already assigned on the
»Basic settings, model« menu.)
position, "A" to "F", using the selection keys on the
left or right touch pad, a switch (whether a "normal"
switch or an expanded switch) is then assigned
as described in the section "Assigning transmitter
controls, switches and control switches" (page 56).
The order in which assignment is made is irrelevant:
you must ensure only that you assign what are,
for you, the "correct" switches. (In the helicopter
program, for example, you should also take care
to ensure you do not use this menu to re-assign
any auto-rotation switch already assigned on the
»Basic settings, model« menu.)
Example: 4 fl ight phases with phase priority
P H A S E A S S I G N M E N T
prior
C
1 Nor mal
combi
A
B
D
E
F
2
6
7
Assigning fl ight phases to switch positions
Now that names have been assigned to the fl ight
phases (1 … max. 8) in the »Phase settings« menu
and also programmed switches in this menu, but …
at the bottom right of the display screen, you only
see <1 Normal > – regardless of the positions the
switches are in!?
Use the selection keys on the left or right touch pad to
move the marker frame down and to the right and then
briefl y tap the center
phases (1 … max. 8) in the »Phase settings« menu
and also programmed switches in this menu, but …
at the bottom right of the display screen, you only
see <1 Normal > – regardless of the positions the
switches are in!?
Use the selection keys on the left or right touch pad to
move the marker frame down and to the right and then
briefl y tap the center
SET
key of the right touch pad: