Netgear MP115 用户手册

 

 

 

 

Page 27 of 36   

2BDF0-020017 REV.00 

 

If you are having problems with your product, check this list of problems and possible solutions before 

requesting service. You may be able to solve the problem yourself. 

If you need to call a customer service representative, please know the model number and serial number of 

your product before you call. This information is on the bottom of the product. Also, please take a moment 

to identify the problem you are having, and be prepared to explain this to the representative. If you believe 

the representative will need to help you with operations, please stay near the product. Our representatives 

will be happy to assist you. 

 

    • Make sure your TV is displaying the appropriate video source. You may need to use the Input, Source, 

 

 

   

Select, or TV/Video button on your TV or TV remote to change video sources. If you are having trouble 

 

 

   

changing the video source, refer to the instructions that came with your TV. 

    • If you did not connect the Digital Media Player directly to your TV but are instead passing the signal 

 

 

   

through your VCR, make sure your VCR is displaying the appropriate video source. You may need to 

use 

 

 

   

the Input or Source button on your VCR or VCR’s remote control. Some VCRs only pass the signal 

 

 

   

through when they are turned off. If you are having trouble displaying the correct video source, refer to 

 

 

   

the instructions that came with your VCR. 

    • Make sure cables are connected to the IN jack on your TV or VCR, not the OUT jack. 

    • The cables you are using to connect your Digital Media Player to your TV or other equipment may be 

 

 

   

damaged or defective. Try exchanging the cables connected to the Digital Media Player with other cables 

 

 

   

that you know are working properly. 

    • Make sure you have firmly attached the AC power cord plug to the rear of the Digital Media Player. Also 

 

 

   

, verify the AC power cord is plugged into a working power outlet and that the outlet is not controlled by 

 

 

   

a light switch. 

 

    • Make sure the batteries are inserted correctly. 

    • Try removing the batteries and reinserting them without touching any buttons on the remote control. 

    • Inspect or replace the batteries with new ones. 

    • Aim the remote at IR (infrared) sensor on the front of the Digital Media Player (not the TV). 

    • Remove any obstacles between the Digital Media Player and remote control. Move closer to the Digital 

 

 

   

Media Player and try the remote again. 

 

    • Make sure your PC is powered on and that it has not entered standby mode. Change your PC’s power 

 

 

   

settings if you want your content to always be available. 

    • Make sure the media server software is running on your PC. Look for the media server icon in your 

 

 

   

system tray. If necessary, start the media server software again. 

    • Click on the media server icon and select Setting to verify you are sharing the correct directories. 

    • If you are using a wireless network, try locating the Digital Media Player closer to your access point or 

 

 

   

wireless PC. 

    • If you are using a wired network, verify the Digital Media Player network cable is properly attached to 

 

 

   

your network hub or router, and that the hub or router has power. 

    • If you are using static network addresses, verify the network address and netmask are correct for your 

 

 

   

network, and that the address is not already in use by another PC or device. 

 

    • Make sure the audio cables are properly connected. 

    • If the audio cables are connected to your TV, the TV must be on to hear any music. 

    • If the audio cables are connected to your stereo receiver, make sure the stereo receiver is on and you 

 

 

   

have the correct stereo input source selected. If you are having trouble selecting the correct audio source, 

 

 

   

refer to the instructions that came with your stereo receiver. 

    • Make sure you did not connect the Digital Media Player’s COAXIAL digital audio out jack to an analog 

 

 

   

jack on the stereo receiver. (Analog audio jacks are usually labeled as such and are usually red and white. 

 

 

   

Coaxial jack is usually orange.) 

    • To perform an audio test, select the music jukebox and then press the options button. Select the audio 

 

 

   

test option to play a brief audio test on your speakers.