Honeywell International Inc. CS22A 用户手册

©2010 Honeywell International Inc.   All rights reserved. 

ACC-PT-QS Rev (a) 4/10

This device complies with part 15 of the FCC Rules.  Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules.  These limits are 

designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, 

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol-

lowing measures:
•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio or television technician for help.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.  The user may find the following 

booklet helpful: “Something About Interference.”  This is available at FCC local regional offices.  Honeywell is not responsible for any radio or television 

interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than 

those specified by Honeywell.  The correction is the responsibility of the user.  
Use only shielded data cables with this system.
Caution:  Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this 

equipment.

UL listed: UL60950-1.

This Class B digital apparatus complies with Canadian ICES-003.  Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada. Son fonctionnement est assujetti aux conditions suivantes :
1. Cet appareil ne doit pas causer de brouillage préjudiciable.
2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un fonctionnement indésirable.  

 cUL listed: CSA C22.2 No.60950-1-03.

The CE marking indicates compliance to 2004/108/EC EMC Directive with Standards EN55022 CLASS B, EN55024, EN61000-3-2, EN61000-

3-3. In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with recommended power supply.
For further information please contact:

Honeywell Imaging & Mobility Europe BV

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands
Honeywell International Inc. shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not 

CE marked and does not comply with the Low Voltage Directive.

Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and 

electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and 

the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to 

use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in 

a sound way.

The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the 

appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.

You may also contact your supplier for more information on the environmental performances of this product.

Please refer to the product packaging for patent information.

Conforms to AS/NZS 3548 EMC requirement

  Conforms to NOM-019.