Zebra Technologies Corporation MD-BTC2TY 用户手册
30
QL 420 User’s Guide
Wireless Local Area Network (WLAN) Module Using
PCMCIA Radio
PCMCIA Radio
The following section only applies when the PCMCIA WLAN module (FCC ID: I28-
QL420352) is installed in the QL 420 printer (note that only one of the radio options can
be installed in the printer at one time). The FCC ID number label is on the front of the
module and can be read with the module installed.
QL420352) is installed in the QL 420 printer (note that only one of the radio options can
be installed in the printer at one time). The FCC ID number label is on the front of the
module and can be read with the module installed.
WARNING: Use of the QL 420 with the radio module marked
with FCC ID: I28-QL420352 meets the FCC requirements for
radio frequency (RF) radiation exposure in the standard body
worn configuration with no minimum separation. In this
configuration, which applies whether the belt clip or shoulder
strap is used, the face of the printer from which paper is
transported is facing away from the user’s body. The standard
configuration must always be used when the printer is body
worn. This configuration maintains the required 1 cm separation
distance.
The printer with this radio option has been SAR tested. The
maximum SAR value measured was 1.04. W/kg averaged over
1 gram.
radio frequency (RF) radiation exposure in the standard body
worn configuration with no minimum separation. In this
configuration, which applies whether the belt clip or shoulder
strap is used, the face of the printer from which paper is
transported is facing away from the user’s body. The standard
configuration must always be used when the printer is body
worn. This configuration maintains the required 1 cm separation
distance.
The printer with this radio option has been SAR tested. The
maximum SAR value measured was 1.04. W/kg averaged over
1 gram.
European Regulatory Information for this Radio
AUS
B
DK
FIN
F
D
GR
IRE
I
LUX
NL
P
E
S
UK
Note: -Member states in the EU with restrictive use for this device are
crossed out!
This device is also authorized for use in all EFTA member states (CH,
ICE, LI, NOR)
crossed out!
This device is also authorized for use in all EFTA member states (CH,
ICE, LI, NOR)
Europe EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE
Directive 1999/5/EC. The following test methods have been applied in
order to prove presumption of compliance with the R&TTE Directive 1999/
5/EC:
• EN 300 328-2 V1.3.1 (2001-12)- Technical requirements for spread-
spectrum radio equipment
• EN 301 489-17 V1.2.1 (2002-08)- EMC requirements for spread-
spectrum radio equipment
In France there are restrictions in the use of this device. A restricted
frequency band exists in France. When operating this device on French
territory you may only use channels 10 and 11 (2457 and 2463 MHz). It is
not allowed to operate this device at any other frequency supported by the
device. For more information see http://www.anfr.fr/
This device complies with the essential requirements of the R&TTE
Directive 1999/5/EC. The following test methods have been applied in
order to prove presumption of compliance with the R&TTE Directive 1999/
5/EC:
• EN 300 328-2 V1.3.1 (2001-12)- Technical requirements for spread-
spectrum radio equipment
• EN 301 489-17 V1.2.1 (2002-08)- EMC requirements for spread-
spectrum radio equipment
In France there are restrictions in the use of this device. A restricted
frequency band exists in France. When operating this device on French
territory you may only use channels 10 and 11 (2457 and 2463 MHz). It is
not allowed to operate this device at any other frequency supported by the
device. For more information see http://www.anfr.fr/
0336
Important Notice:
This device is a portable RF printer intended for com-
mercial and industrial use
This device is a portable RF printer intended for com-
mercial and industrial use
in all EU and EFTA member
states except in France where restrictive use applies.