Xmark Corporation IPSR 用户手册

4  Install the Mounting Plate. Referring to the facility floor 

plan, decide the position of the Receiver. Do not place 
near metal objects and structural frames. Ensure that the 
service light will be visible and that space is allowed for 
the antennas.  Install the mounting plate using one of 
the following methods. 

A  Fasten to a suspended ceiling guy wire, using:

•  1 multi-function Caddy clip 
•  2 machine screws
•  2 hex nuts
•  2 lock washers, OR 

B  Install directly to a ceiling or a wall using:

•  2 wood screws
•  2 hollow wall anchors, OR
Install to a receptacle box, using:
•  2 machine screws

5  Install the Receiver to the Mounting Plate.

Plug  the  wired  terminal  block  into  the  Receiver  and 
install the Receiver onto the Mounting Plate, using the 
screws removed in Step 2. DO NOT place excess net-
work and power supply wires inside the Receiver case.

6  Attach the two clips to lock the antennas in place. 

Once all devices are installed, 
power  up  the  Receiver  and 
other  devices.  Using  the  PS 
System  Manager,  run  Auto  Configure  to  install  the  new 
devices, and then configure them for operation.
The coverage area of the Receiver must also be checked.  

The green status light is located on the front of the 
Receiver, and indicates the current status of the Receiver.

Off

No tags within range or no power.

Flashing 

coincident with 

tag transmissions

The Receiver is receiving tag 

transmissions. 

Flashing steady 

for two seconds, 

off for one 

second repeatedly

Wink command currently operating.

NOTE: Intermittent flashes between 

the steady two second flash indicates 

the presence of tags within the area.

On

Failure. Check power connections or 

download firmware to the Receiver 

using the PS System Manager.

•  Position the Receiver beneath ceiling obstructions—

When  installing  above  drop  ceilings,  mount  the 
Receiver below metal duct work and pipes

•  If ceiling tiles are foil-backed, mount Receiver below. 
•  Route cables up and away from the Receiver—When 

the cable is not in conduit, route it directly away from 
the Receiver for at least 1 foot (30 cm). 

•  Install the Receiver temporarily until testing is com-

plete—Fastenings should be secure enough that the 
Receiver can be permanently mounted without dis-
turbing its orientation.

•  Point the horizontal antenna into a clear area, away 

from  metal  objects—One  antenna  always  points 
downwards, with the second antenna (horizontal) at 
a 90 degree angle (can be adjusted to suit site condi-
tions). Make sure the horizontal antenna is not run-
ning parallel to cabling in the ceiling. 

•  Observe  temperature  and  humidity  restrictions—

Refer to the Specifications table. 

•  Leave slack in the cable—Leave at least 10 ft. (3 m) 

of slack in the communication and power cables to 
allow for adjustments in the location of the Receiver. 

•  No user adjustments to internal circuitry—Tampering 

may cause component or system failure, or both, and 
will void the warranty.

The steps below correspond to the numbers in Figure 1.
1  Record the LonWorks Neuron ID number.

Locate and record the LonWorks Neuron ID number 
onto the facility floor plan indicating the Receiver’s 
position and network wiring path. Affix one of the 
supplied Neuron ID labels on the floor plan and affix 
the other on the Receiver in a visible location.

2  Remove  the  Mounting  Plate  from  the  Receiver  by 

sliding  it  off.  If  the  Receiver  is  to  be  installed  to  a 
receptacle box, pass the network and power supply 
wires through the hole in the Mounting Plate. 

3  Wire the terminal block.

Connect the LonWorks Network IN, Network 
OUT, and Power Supply to the terminals. If the 
Receiver is at the end of the network segment, 
then terminate the network segment with a 105 Ω 
terminator.  

•  Ensure that the power supply and net-

work are turned off to prevent electrical 
shock or damage to equipment. 

•  Touch your hand to ground to discharge 

any electrostatic charge before handling 
the Receiver.

Patient Security Receiver Installation Guide