Lutron Electronics Company Inc 0108 用户手册

Lutron Electronics Co., Inc., 7200 Suter Road

Coopersburg, PA 18036-1299 U.S.A.

 B  Hold the indicated button on each transmitter 

for 6 seconds. The fixture will flash to show that 

wireless transmitters have been associated.  

To associate another transmitter, repeat steps 

4A and 4B.

 

A  Initiate association mode on the Project 37 Control Module by shining a green 

laser pointer at the laser detection hole on the sensor until the load attached to 

the Project 37 Control Module starts flashing every 2 seconds.

 

  Alternatively, press and hold the toggle button for 6 seconds on the Project 37 

Control Module to initiate association mode.

Laser Detection (smallest)

Associate Wireless Transmitters to Project 37 Control Module

Before beginning this step, make sure that there are no other Project 37 Control 

Modules being set up in the building which are currently in this 

association mode.. It is possible that wireless transmitters from other systems can be incorrectly associated to this module.

  Green laser specifications: 

•  Wave output: constant

•  Wavelength: 532 nm

•  Output power: 5 mW maximum

Technical Assistance  |  1.800.523.9466  USA, Canada, and the Caribbean  |  +44.(0)20.7702.0657 Europe  |  +1.610.282.3800 Others  |  www.lutron.com     

041467 

Rev. A

07/2014

Project 37 

|

 Installation

Required Components

Project 37 Occupancy/Vacancy and  

Daylight Sensor 

(1 maximum)

Pico

®

 Wireless 

Control

(10 maximum)

6 mA maximum for the control lines. Switches up to 1 A total. May be  

pre-installed in light fixture. 

Project 37 Control Module with 0 –10 V

Raise

Toggle

Lower

Load Status LED

Consult third-party 0 – 10 V fixtures installation guide for fixture-specific wiring. 

On

All lights 100%

Favorite All lights 50%
Off

All lights off

Default Functionality

All Wireless  

Transmitters  

must be  

installed within  

30 ft (9 m) of the  

Project 37 Control Module.

Control: 0–10 V-  6 mA

For installation by a qualified electrician in accordance with all 

local and national electrical codes.

• Note: Use copper conductors only.

•  Check to see that the device type and rating is suitable for the 

application.

•  DO NOT install if product has any visible damage.

•  If moisture or condensation is evident, allow the product to dry 

completely before installation.

•  Operate between 0 °C and 40 °C, ambient.

•  0% to 90% humidity, non-condensing.

•  For indoor use only.

120 – 277  V~  50 / 60 Hz  1 A

FC-1 (Project 37 
Control Module)

UL 2043 Plenum Rated

12 V-  25 mA

FC-0  
(Project 37 Sensor)

Sensor

Pico

®

  

Wireless  

Control

Project 37 

Control 

Module

40 ft (12 m)

30 ft (9 m)

PIR Lens

Laser Detection

Daylight Lens

Note:  Project 37 Control Module can be used without a Sensor

Install control module directly to fixture or  

in junction box nearest the fixture. Install sensor 

in ceiling near fixture so as to optimize cover-

age in the desired area.

Radio Powr Savr

TM

 

Occupancy/Vacancy Sensor

(10 maximum)

Install Project 37 Control Module 

and Sensor

Suggested Installation Location: Close to the 

Fixture/Troffer.

 

  The Project 37 Control Module can be installed in a 

fixture/troffer, junction box or marshalling box using the 

conduit nut (provided) or with mounting screws (not 

provided). Please consult local and national electric 

codes for proper installation.
If installing unit inside a junction box, please see 

Application Note #423 at  

www.lutron.com/TechnicalDocumentLibrary/048423.pdf

 

B  Ideally mount the sensor to the ceiling tile close to the 

fixture using the wire form or using the command strips 

(included). The 2 communication wires from the sensor 

attaches to the control module poke in connectors. 

 

C  Once installed, energize the Project 37 Control Module.

Green/Yellow

Neutral

Switched 
Hot/Live

Violet

Gray

Fixture Earth

+

–

To additional 0 – 10 V fixtures

Hot (Black)

Neutral

+

–

NEU

HO

T

Class 2

MAINS

+

–

NEU

HOT

Class 

2

MAIN

S

Switched Hot (Red)

Hot (Black)

Neutral (White)

Neutral

Fixture/Troffer 
or Junction 
Box

1/2 in (21 mm) Knockout Opening

Conduit Nut

From back of sensor

Violet
Gray

Fixture Earth

Green/Yellow

Spring arms

Note:  For solid ceilings or 

others where the wireform 

cannot be utilized, use the 

supplied Command strips 

to adhere sensor to desired 

location on ceiling or fixture.

Sensor Detection Range

Install the Sensor

The Project 37 sensor mounts to the ceiling surface with a supplied wireform clip. 

Two wires connect to the control module and can either be routed through a hole in 

the ceiling or across the ceiling surface. DO NOT install on ceilings higher than 12 ft 

(3.7 m). The sensor should be installed in a location where it has a good view of the 

space that it is meant to cover. 

15 ft 

(4.6 m)

9 ft 

(2.7 m)

3 ft 

(0.9 m)

0

3 ft 

(0.9 m)

9 ft 

(2.7 m)

15 ft 

(4.6 m)

400 ft

2

 (37 m

2

) maximum coverage 

area of one sensor when  mounted 

on an 9 ft (2.75 m) ceiling

Ceiling

Floor

9 ft  

(2.75 m)

15 ft 

(4.6 m)

9 ft 

(2.7 m)

3 ft 

(0.9 m)

0

3 ft 

(0.9 m)

9 ft 

(2.7 m)

15 ft 

(4.6 m)

15 ft 

(4.6 m)

9 ft 

(2.7 m)

3 ft 

(0.9 m)

0

3 ft 

(0.9 m)

9 ft 

(2.7 m)

15 ft 

(4.6 m)

 

Slide closed end of wire form under 

the two retention arms on the back 

of the sensor

 

While continuing to push against the 

retention arms, rock the other side of 

the wireform down against the sensor 

and slide them into place under the 

loop retention features

 

Push wireform through tile and 

bend on the backside of the tile to 

complete the mounting.