JVC KENWOOD Corporation 31201110 用户手册
5
TRANSMITTING
2 YOUR FIRST QSO (HF/ 50 MHz band)
q
Turn the Tuning control to tune in a desired
station or to select an unused frequency.
w
Press [AT/ ANT 1/2] momentarily.
•
“AT” appears.
e
Press and hold [AT/ ANT 1/2] to activate the
built-in antenna tuner.
built-in antenna tuner.
•
“AT” starts blinking and the MAIN band LED
above the [MIC/ CAR] key turns red.
above the [MIC/ CAR] key turns red.
•
Tuning should be completed in under
20 seconds, then “AT” stops blinking.
20 seconds, then “AT” stops blinking.
•
If tuning is not completed within 20 seconds,
error beeps sound. Press [AT/ ANT 1/2] to
stop the error beeps and quit tuning. Check
your antenna system before continuing. If you
do not press [AT/ ANT 1/2], tuning will continue
for approximately 60 seconds.
error beeps sound. Press [AT/ ANT 1/2] to
stop the error beeps and quit tuning. Check
your antenna system before continuing. If you
do not press [AT/ ANT 1/2], tuning will continue
for approximately 60 seconds.
Note: You will hear a lot of clicking sounds coming from the
transceiver while the antenna tuner is trying to tune the
antenna. This is simply the relay switches turning ON and OFF.
transceiver while the antenna tuner is trying to tune the
antenna. This is simply the relay switches turning ON and OFF.
r
With LSB, USB, or AM selected, press
[MIC/ CAR] to activate the Microphone Gain
Adjust.
[MIC/ CAR] to activate the Microphone Gain
Adjust.
•
“MIC GAIN 50” appears.
•
With FM selected, skip this step.
t
Press [SEND].
•
The MAIN band LED turns red.
y
Begin speaking into the microphone in your
normal tone of voice.
normal tone of voice.
u
LSB/ USB: While speaking into the
microphone, adjust the MULTI/ CH control so
that the ALC meter reflects according to your
voice level.
microphone, adjust the MULTI/ CH control so
that the ALC meter reflects according to your
voice level.
AM: While speaking into the microphone,
adjust the MULTI/ CH control so that the
calibrated power meter slightly reflects to your
voice level.
adjust the MULTI/ CH control so that the
calibrated power meter slightly reflects to your
voice level.
FM: Skip this step.
i
When you finish speaking, press [SEND] to
return to receive mode.
o
Press [MIC/ CAR] to quit the Microphone Gain
Adjustment.
Adjustment.
Note: If desired, access Menu No. 41 {page 28} to try the
Microphone Gain Adjust for FM.
Microphone Gain Adjust for FM.
This completes your introduction to the
TS-2000(X), but there is a great deal more to
know. “OPERATING BASICS” {page 18} and the
following chapters explain all the functions of this
transceiver, starting with the most basic,
commonly-used functions.
TS-2000(X), but there is a great deal more to
know. “OPERATING BASICS” {page 18} and the
following chapters explain all the functions of this
transceiver, starting with the most basic,
commonly-used functions.
PF
F LOCK A
1
CH1/REC
2
CH2/REC
3
CH3/REC
4
TONE/SEL
5
METER
6
CTCSS/SEL
7
NB/LEVEL
8
AGC/OFF
9
FINE/STEP
.
DCS/SEL
0
SHIFT/OFFSET
ENT
SEND
PHONES
MIC
AT
ANT1/2
PROC
LEVEL
VOX
ATT
PRE
LEVEL
LEVEL
LEVEL
MANUAL
LO/
WIDTH
HI/
SHIFT
N.R.
A.N.
B.C.
F
U
N
CALL
C.IN
CLR
MAIN
AUTO
CAR
TX MONI
DELAY
NAR
REV
MIC
PWR
KEY
LSB
USB
CW
FSK
FM
AM
SUB
DISP
SEL
1MHz
CTRL
MR
MG.SEL
M.IN
QUICK MEMO
M/S
REV
TRACE
MAIN
MANUAL
RF
AF
SQL
SUB
CH
MULTI
BC
MAIN
GAIN
VFO/CH
MENU
TF-
SET
MAIN
SUB
SG.SEL
SCAN
M VFO
M.IN
RIT
CW TUNE
9.6k STA
RIT/SUB
CON
XIT
ALT
SET
CLEAR
P.C.T
_
+
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
SA
TL
A/B
VFO/M
SPLIT
A=B
4 9
7
1
8
5
3
2
FILTER
S
1
3
5
7
9
20
40
60dB
PWR
10
25
50
100W
ALC
FILTER
S
1
3
5
7
9
20
40
60dB
PWR
10
25
50
100W
ALC
PWR
10
25
50
100W
FILTER
S
1
3
5
7
9
20
40
60dB
ALC