JVC KENWOOD Corporation 31201110 用户手册
YOUR FIRST QSO (VHF/ UHF band)
6
YOUR FIRST QSO
RECEIVING
e
Press [MAIN], then confirm that VFO A has
been selected for communications; “
been selected for communications; “
t
A”
should be visible on the display. If it has not,
press [A/B] to select VFO A.
press [A/B] to select VFO A.
r
Turn the MAIN AF control slowly clockwise
until you hear a suitable level of background
noise.
until you hear a suitable level of background
noise.
t
Press [+] or [–] to move up to the VHF
(144 MHz) or UHF (430/ 440 MHz) Amateur
radio band.
(144 MHz) or UHF (430/ 440 MHz) Amateur
radio band.
If your primary operating band is VHF (144 MHz) or UHF (430/ 440 MHz), the TS-2000(X) can also serve you
as a powerful All-mode VHF/ UHF transceiver. The instructions below are intended only for a quick guide to
get you up on the air on the VHF/ UHF band. If you encounter problems or there is something you don’t
understand, read the detailed explanations given later in this manual.
as a powerful All-mode VHF/ UHF transceiver. The instructions below are intended only for a quick guide to
get you up on the air on the VHF/ UHF band. If you encounter problems or there is something you don’t
understand, read the detailed explanations given later in this manual.
Note: This section explains only keys and controls required to
briefly try the transceiver.
briefly try the transceiver.
q
Set the following as specified:
•
MAIN AF:
Fully counterclockwise
•
MAIN RF GAIN: Fully clockwise
•
MAIN SQL:
Fully counterclockwise
w
Switch ON the DC power supply, then press
and hold [ ] (POWER) briefly on the
transceiver.
and hold [ ] (POWER) briefly on the
transceiver.
•
Do not press the switch for more than
approximately 2 seconds; the transceiver
will be switched OFF.
approximately 2 seconds; the transceiver
will be switched OFF.
•
Upon power up, “HELLO” appears,
followed by the selected frequency and
other indicators.
followed by the selected frequency and
other indicators.
y
Confirm that the operating mode is FM. If it is not,
press [FM/ AM/ NAR] to select FM.
press [FM/ AM/ NAR] to select FM.
u
Turn the SQL control clockwise until the
background noise is just eliminated; The MAIN
band LED turns off.
background noise is just eliminated; The MAIN
band LED turns off.
i
Turn the Tuning control to tune in a station.
•
You can use the MULTI/ CH control to change
the frequency faster. If you do not hear any
stations, the antenna may not be installed or
connected properly. Check the antenna
connector on the rear panel {page 13}.
the frequency faster. If you do not hear any
stations, the antenna may not be installed or
connected properly. Check the antenna
connector on the rear panel {page 13}.
PF
F LOCK A
1
CH1/REC
2
CH2/REC
3
CH3/REC
4
TONE/SEL
5
METER
6
CTCSS/SEL
7
NB/LEVEL
8
AGC/OFF
9
FINE/STEP
.
DCS/SEL
0
SHIFT/OFFSET
ENT
SEND
PHONES
MIC
AT
ANT1/2
PROC
LEVEL
VOX
ATT
PRE
LEVEL
LEVEL
LEVEL
MANUAL
LO/
WIDTH
HI/
SHIFT
N.R.
A.N.
B.C.
F
U
N
CALL
C.IN
CLR
MAIN
AUTO
CAR
TX MONI
DELAY
NAR
REV
MIC
PWR
KEY
LSB
USB
CW
FSK
FM
AM
SUB
DISP
SEL
1MHz
CTRL
MR
MG.SEL
M.IN
QUICK MEMO
M/S
REV
TRACE
MAIN
MANUAL
RF
AF
SQL
SUB
CH
MULTI
BC
MAIN
GAIN
VFO/CH
MENU
TF-
SET
MAIN
SUB
SG.SEL
SCAN
M VFO
M.IN
RIT
CW TUNE
9.6k STA
RIT/SUB
CON
XIT
ALT
SET
CLEAR
P.C.T
_
+
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
SA
TL
A/B
VFO/M
SPLIT
A=B
6
2
1
8
5
3
1 7
1 4
FILTER
S
1
3
5
7
9
20
40
60dB
PWR
10
25
50
100W
ALC
FILTER
S
1
3
5
7
9
20
40
60dB
PWR
10
25
50
100W
ALC