JVC KENWOOD Corporation 31201110 用户手册

12

$4

 RIT/SUB control

After switching the RIT or XIT function ON, turn this
control to select the desired frequency offset {pages
38, 40}.

Turn to adjust the sub-receiver frequency when the
RIT and XIT functions are switched OFF and the sub-
receiver is switched ON {page 45}.

$5

 MANUAL BC control

Turn to adjust the audio notch frequency while the
DSP beat cancel function is set to manual audio
notch filter mode {page 56}.

$6

 MAIN RF GAIN control

Turn to adjust the radio frequency gain for the main
transceiver {page 18}.

$7

 MULTI/ CH control

In VFO mode, rotate to step the operating frequency
up or down {page 37}.  In memory channel mode,
rotate to select a memory channel {page 58}.  Also
used for selecting Menu numbers when accessing the
Menu mode {page 21} and as a selector to choose
settings for various functions activated by front panel
buttons.  The MULTI/ CH LED lights when the
setting(s) can be changed using the MULTI/ CH
control.

$8

 MAIN SQL control

Used for muting (“squelching”) the speaker, head
phone and AF output on ACC2 (13-pin DIN
connector) when no receive signal is present on the
main transceiver {page 19}.

$9

 MAIN AF control

Turn to adjust the volume on the main transceiver
{page 19}.

%0

 SUB SQL control

Used for muting (“squelching”) the speaker, head
phone and AF output on ACC2 (13-pin DIN
connector)  when no receive signal is present on the
sub-receiver {page 46}.

%1

 SUB AF control

Press to switch the sub-receiver ON or OFF.  When it
is ON, the SUB-receiver LED lights orange.

Turn to adjust the volume for the sub-receiver.

%2

 LO/ WIDTH control

Turn clockwise/ counterclockwise to increase/
decrease the value for the low cut-off DSP filter
frequency or the filter bandwidth (CW/ FSK).  The
selected value appears on the main dot-matrix
display {page 55}.

%3

 HI/ SHIFT control

Turn clockwise/ counterclockwise to increase/
decrease the value for the high cut-off DSP filter
frequency or the Shift frequency.  The selected value
appears on the sub dot-matrix display
{page 55}.

%4

 MAIN band LED

Lights green while the main transceiver’s squelch is
open.  Lights red while transmitting on the main
transceiver’s VFO band.

%5

 SUB band LED

Lights green while the sub-receiver’s squelch is open.
Lights red while transmitting on the sub-receiver’s
VFO band.

PF

F LOCK A

1

CH1/REC

2

CH2/REC

3

CH3/REC

4

TONE/SEL

5

METER

6

CTCSS/SEL

7

NB/LEVEL

8

AGC/OFF

9

FINE/STEP

.

DCS/SEL

0

SHIFT/OFFSET

ENT

SEND

PHONES

MIC

AT

ANT1/2

PROC

LEVEL

VOX

ATT

PRE

LEVEL

LEVEL

LEVEL

MANUAL

LO/

WIDTH

HI/

SHIFT

N.R.

A.N.

B.C.

F

U

N

CALL

C.IN

CLR

MAIN

AUTO

CAR

TX MONI

DELAY

NAR

REV

MIC

PWR

KEY

LSB

USB

CW

FSK

FM

  AM

SUB

DISP

SEL

1MHz

CTRL

MR

MG.SEL

M.IN

QUICK MEMO

M/S

REV

TRACE

MAIN

MANUAL

RF

AF

SQL

SUB

CH

MULTI

BC

MAIN

GAIN

VFO/CH

MENU

TF-

SET

MAIN

SUB

SG.SEL

SCAN

M  VFO

M.IN

RIT

CW  TUNE

9.6k STA

RIT/SUB

CON

XIT

ALT

SET

CLEAR

P.C.T

_

+

HF/VHF/UHF ALL MODE MULTI BANDER TS-2000

SA

TL

A/B

VFO/M

SPLIT

A=B

47

46

54

55

44

45

53

52

51

50

49

48