JVC KENWOOD Corporation 31201110 用户手册
4 GETTING ACQUAINTED
13
REAR PANEL
q
ANT 1 and ANT 2 connectors
Connect your primary HF/ 50 MHz antenna to ANT1.
If you are using 2 antennas for the HF/ 50 MHz band,
connect the secondary antenna to the ANT2
connector.
If you are using 2 antennas for the HF/ 50 MHz band,
connect the secondary antenna to the ANT2
connector.
w
GND post
Connect a heavy gauge wire or copper strap between
the ground post and the nearest earth ground
{page 2}.
the ground post and the nearest earth ground
{page 2}.
e
KEY and PADDLE jacks
The PADDLE jack mates with a 6.3 mm (1/4")
3-conductor plug for connecting a keyer paddle to the
internal electronic keyer. The KEY jack mates with a
3.5 mm (1/8") 2-conductor plug for connecting an
external key for CW operation. Read “Keys and
Keyboards for CW Operation” {page 3} before using
these jacks.
3-conductor plug for connecting a keyer paddle to the
internal electronic keyer. The KEY jack mates with a
3.5 mm (1/8") 2-conductor plug for connecting an
external key for CW operation. Read “Keys and
Keyboards for CW Operation” {page 3} before using
these jacks.
r
AT connector
Mates with the connector on the cable supplied with
the external antenna tuner. Refer to the instruction
manual supplied with the tuner for more information.
the external antenna tuner. Refer to the instruction
manual supplied with the tuner for more information.
t
ANT 144
Connect your 144 MHz band antenna to this
connector.
connector.
y
ANT 430
Connect your 430 (440) MHz band antenna to this
connector.
connector.
u
ANT 1.2G (TS-2000 Optional)
Connect your 1.2 GHz band antenna to this
connector.
connector.
i
DC 13.8V power input connector
Connect a 13.8 V DC power source to this connector
{page 2}. Use the cable supplied with the regulated
DC power supply.
{page 2}. Use the cable supplied with the regulated
DC power supply.
o
COM connector
Mates with a 9-pin female RS-232C connector for
connecting a computer via one of its serial
communication ports {page XX}. Also used with the
Quick Data Transfer function {page XX}.
connecting a computer via one of its serial
communication ports {page XX}. Also used with the
Quick Data Transfer function {page XX}.
!0
PANEL connector
Connect a cable from the optional separate remote
panel (RM-2000) to this connector.
panel (RM-2000) to this connector.
!1
EXT.SP1 and EXT.SP2 jacks
Mate with a 3.5 mm (1/8"), 2-conductor (mono) plugs
for connecting external speakers {pages 3, 78}.
for connecting external speakers {pages 3, 78}.
!2
EXT.CONT connector
Connect your 50 MHz, 144 MHz, 430 (440) MHz or
1.2 GHz linear amplifier control cable to this
connector {page 76}.
1.2 GHz linear amplifier control cable to this
connector {page 76}.
!3
ACC2 connector
Mates with a 13-pin male DIN connector for
connecting various accessory equipment, such as an
external TNC or a RTTY terminal {page XX, XX}.
connecting various accessory equipment, such as an
external TNC or a RTTY terminal {page XX, XX}.
!4
REMOTE connector
Mates with a 7-pin male DIN connector for connecting
an HF linear amplifier {page 76}. Do not connect
50 MHz, 144 MHz, 430 (440) MHz, or 1.2 GHz linear
amplifier controls to this connector; use the
EXT.CONT connector instead.
an HF linear amplifier {page 76}. Do not connect
50 MHz, 144 MHz, 430 (440) MHz, or 1.2 GHz linear
amplifier controls to this connector; use the
EXT.CONT connector instead.
!5
HF RX ANT connector
Connect a separate receive-only antenna for HF
bands to this jack (RCA connector) {page XX}.
bands to this jack (RCA connector) {page XX}.
EXT. SP2
8
Ω
PANEL
COM
ANT 2
ANT 1
ANT
144
AT
ANT 1.2G
DC
13.8V
ANT
430
EXT. SP1
8
Ω
ACC2
EXT. CONT
REMOTE
HF
RX ANT
RX ANT
PADDLE
KEY
GND
2
1
1
9
10
12
13
14
15
11
3
2
4
5
8
6
7