Visonic Inc. MCT442 用户手册
D-300273
1
MCT
MCT
MCT
MCT----442
442
442
442
Supervised Indoor Wireless CO Gas Detector
Installation Instructions
1. INTRODUCTION
The carbon monoxide (CO) detector is designed to monitor the
CO gas level in residential dwellings and give early warning
before potentially dangerous levels exist. The CO alarm is
transmitted to the PowerMax+ (version F and up) or PowerMax
Pro and presented on its display.
CO gas level in residential dwellings and give early warning
before potentially dangerous levels exist. The CO alarm is
transmitted to the PowerMax+ (version F and up) or PowerMax
Pro and presented on its display.
The CO gas is considered to be a highly dangerous poisonous
gas because it is colorless, odorless, tasteless and very toxic.
Presence of CO gas inhibits the blood's capacity to transport
oxygen throughout the body, which can eventually lead to brain
damage. CO gas is produced by incomplete combustion of fuels
(such as natural gas, propane, heating oil, kerosene, coal,
charcoal, gasoline or wood) that can occur in any device that
depends on burning for energy and heat (such as furnaces,
boilers, room heaters, hot water heaters, stoves, grills and in any
gasoline powered vehicle or engine).
gas because it is colorless, odorless, tasteless and very toxic.
Presence of CO gas inhibits the blood's capacity to transport
oxygen throughout the body, which can eventually lead to brain
damage. CO gas is produced by incomplete combustion of fuels
(such as natural gas, propane, heating oil, kerosene, coal,
charcoal, gasoline or wood) that can occur in any device that
depends on burning for energy and heat (such as furnaces,
boilers, room heaters, hot water heaters, stoves, grills and in any
gasoline powered vehicle or engine).
Before CO harmful level is reached, the detector's internal buzzer
beeps sound periodically and the detector's red LED flashes. In
this condition, the buzzer sound can be stopped for 6 minutes by
pressing the TEST/MUTE switch. It will not correct the CO gas
problem, but will temporarily silence the buzzer while you correct
the problem. After 6 minutes, the detector restarts alarm if the CO
level remains high.
beeps sound periodically and the detector's red LED flashes. In
this condition, the buzzer sound can be stopped for 6 minutes by
pressing the TEST/MUTE switch. It will not correct the CO gas
problem, but will temporarily silence the buzzer while you correct
the problem. After 6 minutes, the detector restarts alarm if the CO
level remains high.
The detector provides
low battery and detector
end-of-life indications.
low battery and detector
end-of-life indications.
Caution
: The
detector expiry date is
stamped on the
detector. After the
expiry date, the
detector should not
be used - do not wait
for end-of-life
indication!!
stamped on the
detector. After the
expiry date, the
detector should not
be used - do not wait
for end-of-life
indication!!
Battery
(green) /
Fault
(yellow)
LED
TEST /
MUTE
BUTTON
ALARM
(red) LED
Figure 1 - General View
The detector is continuously self-tested and has a TEST button
that enables the user to test the detector anytime.
that enables the user to test the detector anytime.
Note: The TEST/MUTE switch functions as TEST switch (in
normal operation) or as MUTE switch (in alarm condition).
normal operation) or as MUTE switch (in alarm condition).
The tamper switch actuator (fig. 3), is pressed against the bracket
when the unit is attached to the bracket. Removal of the unit from
the bracket causes the switch contacts to open, creating a tamper
event, which is reported by the transmitter to the alarm system
control panel.
when the unit is attached to the bracket. Removal of the unit from
the bracket causes the switch contacts to open, creating a tamper
event, which is reported by the transmitter to the alarm system
control panel.
2. SPECIFICATIONS
CO DETECTION
Detection principle: Electrochemical cell
Detection principle: Electrochemical cell
Detector Active Life: 5 years maximum
Selectable Sensitivity:
Selectable Sensitivity:
DIP switch in EN Mode
No warning at 30 ppm for 120 minutes, 50 ppm for 60 minutes,
100 ppm for 10 minutes.
Warning at 50 ppm between 60-90 minutes, 100 ppm for 10-40
minutes, 150 ppm within 3 minutes.
No warning at 30 ppm for 120 minutes, 50 ppm for 60 minutes,
100 ppm for 10 minutes.
Warning at 50 ppm between 60-90 minutes, 100 ppm for 10-40
minutes, 150 ppm within 3 minutes.
DIP switch in UL Mode
No warning at 30 ppm for 30 days, 70 ppm for 60 minutes, 150
ppm for 10 minutes, 400 ppm for 4 minutes.
No warning at 30 ppm for 30 days, 70 ppm for 60 minutes, 150
ppm for 10 minutes, 400 ppm for 4 minutes.
Warning at 70 ppm between 60-240 minutes, 150 ppm for 10-
50 minutes, 400 ppm between 4-15 minutes.
50 minutes, 400 ppm between 4-15 minutes.
Audible Alarm Volume: >95db at a distance of 3m (10 ft.).
TRANSMITTER AND CODING
Operating Frequency (MHz): 315, 433.92, 868.95 or other
frequency according to local requirements.
Transmitter's ID Code: 24-bit digital word, over 16 million
combinations, pulse width modulation. PowerCode or Zigbee
Protocols.
Overall Message Length: 36 bits
Supervision: Automatic signaling at 60-minute intervals (315
MHz version), 15-minute interval (433.92, 868.95 MHz versions)
or according to the local standards.
Transmitted Messages: CO gas alarm, low battery, tamper,
sensor end of life (5 years), sensor trouble, supervision.
Tamper Alerts: Tamper message is transmitted to the
PowerMax+ / PowerMax Pro control panel when the detector is
removed from its bracket .
ELECTRICAL DATA
Power Source: 9 volt Lithium battery (Ultra Life #U9VL, U9VL-J).
Current Drain: 11 µA standby, 250 µA in operation
Battery Life Expectancy: At least 1 year (for typical use)
Battery Supervision: Automatic transmission of battery status
data as part of any transmitted message.
Operating Frequency (MHz): 315, 433.92, 868.95 or other
frequency according to local requirements.
Transmitter's ID Code: 24-bit digital word, over 16 million
combinations, pulse width modulation. PowerCode or Zigbee
Protocols.
Overall Message Length: 36 bits
Supervision: Automatic signaling at 60-minute intervals (315
MHz version), 15-minute interval (433.92, 868.95 MHz versions)
or according to the local standards.
Transmitted Messages: CO gas alarm, low battery, tamper,
sensor end of life (5 years), sensor trouble, supervision.
Tamper Alerts: Tamper message is transmitted to the
PowerMax+ / PowerMax Pro control panel when the detector is
removed from its bracket .
ELECTRICAL DATA
Power Source: 9 volt Lithium battery (Ultra Life #U9VL, U9VL-J).
Current Drain: 11 µA standby, 250 µA in operation
Battery Life Expectancy: At least 1 year (for typical use)
Battery Supervision: Automatic transmission of battery status
data as part of any transmitted message.
Visual and Audible Indications:
Visual Indication (LEDs)
Condition
Red Yellow
Green
Audio
Indication
Alarm 4
flashes
(*)
-
-
4 beeps (*)
End of Life
/ Fault
/ Fault
- 3
flashes
every
60 sec.
every
60 sec.
- one
beep
every 60 sec.
Battery OK
-
-
Flashes once
every minute
every minute
-
Low
battery
battery
- 1
flash
every
60 sec.
60 sec.
- one
beep
every 60 sec.
MUTE
button is
pressed (to
silent the
alarm for 6
minutes)
button is
pressed (to
silent the
alarm for 6
minutes)
4 flashes
(*)
(*)
-
-
OFF for 6
minutes (**)
minutes (**)
TEST
button is
pressed
button is
pressed
1 flash
(the 1st
LED)
(the 1st
LED)
1 flash
(the 2nd
LED)
(the 2nd
LED)
Flashes (the
3rd LED) If
CO circuit test
and battery
are OK - lights
during 2 sec.
3rd LED) If
CO circuit test
and battery
are OK - lights
during 2 sec.
1 beep
* Every 5 seconds during the first 4 minutes, every 60 sec. after
the first 4 minutes.
** After 6 minutes, the detector restarts alarm if the CO level
remains high.
Note: Long period of low battery condition may cause improper
function. In case of End-of-Life/Fault indication, replace the
battery and check if the End-of-Life/Fault indication still exists. If it
still exists, stop using the detector.
function. In case of End-of-Life/Fault indication, replace the
battery and check if the End-of-Life/Fault indication still exists. If it
still exists, stop using the detector.
PHYSICAL DATA
Operating Temperature: -10
Operating Temperature: -10
°
C to 40
°
C (14
°
F to 104
°
F).
Relative Humidity: 10-93%
±
2% RH
Dimensions: 127 mm (5 in.) x 40 mm (1-9/16 in.)
Weight (without battery): 180g (6.35 oz)
Compliance with Standard: EN 50291, UL 2034, BS 7860,
CSA-6.19-01
Weight (without battery): 180g (6.35 oz)
Compliance with Standard: EN 50291, UL 2034, BS 7860,
CSA-6.19-01