UTC Fire & Security Americas Corporation Inc 787E-SIMON 用户手册
20
Programming
Option 40: Trouble Beeps (Default = on)
Determines whether the panel, X-10, and hardwire interior
sirens sound six beeps every minute when a trouble condition
occurs (on) or not (off). The following conditions cause trouble
beeps:
sirens sound six beeps every minute when a trouble condition
occurs (on) or not (off). The following conditions cause trouble
beeps:
❑
AC power failure
❑
Low CPU battery
❑
Sensor failure (supervisory)
❑
Sensor trouble (low battery or tripped tamper)
❑
Fail to communicate
❑
No Activity timer has timed out. Trouble beeps continue
for 5 minutes and if the panel does not see activity, trouble
beeps stop and the panel reports the no activity to the cen-
tral station.
for 5 minutes and if the panel does not see activity, trouble
beeps stop and the panel reports the no activity to the cen-
tral station.
Trouble beeps can be silenced by arming or disarming the sys-
tem, or by pressing the STATUS button. Trouble beeps resume
4 hours later if the trouble condition is not cleared.
tem, or by pressing the STATUS button. Trouble beeps resume
4 hours later if the trouble condition is not cleared.
Note
For UL listed systems, Trouble Beeps must be on.
To turn on Trouble Beeps, press:
Add—Option #—40—DONE.
To turn off Trouble Beeps, press:
Delete—Option #—40—DONE.
Option 41: Chime Voice (Default = off)
Determines whether the panel announces the sensor number
and name (on) or only sounds beeps (off), when the CHIME
Doors or CHIME Special Motion features are on and sensors in
groups 10, 13, and 25 are tripped while the system is disarmed.
and name (on) or only sounds beeps (off), when the CHIME
Doors or CHIME Special Motion features are on and sensors in
groups 10, 13, and 25 are tripped while the system is disarmed.
To turn on Chime Voice, press:
Add—Option #—41—DONE.
To turn off Chime Voice, press:
Delete—Option #—41—DONE.
Option 42: Speaker Level (Default = 8)
Sets the volume of voice messages from the panel speaker.
The volume can be set from 1 (lowest) to 8 (highest). Turning
off this option returns the setting to the default value.
off this option returns the setting to the default value.
To set Speaker Level, press:
Add—Option #—42—1 - 8—DONE.
To turn off Speaker Level (return to default), press:
Delete—Option #—42—DONE.
Option 43: Numeric Pager/Voice Event Notification
Phone Number (Default = off)
Lets you program up to a 26-digit phone number for numeric
pager or voice event notification (on), or delete an existing
phone number (off).
pager or voice event notification (on), or delete an existing
phone number (off).
When used to call a numeric pager, a 3-digit code appears on
the pager display to identify the report. When used to call a
remote phone, a person at the remote phone location can hear
system voice alarm announcements. See the “Testing” section
for more information.
the pager display to identify the report. When used to call a
remote phone, a person at the remote phone location can hear
system voice alarm announcements. See the “Testing” section
for more information.
Press Test for each required pause, Add for a *, and Delete for
a # (each of which uses one of the 26 available places).
a # (each of which uses one of the 26 available places).
Note
Some pagers may require 3 or 4 additional pauses after
the last digit to work correctly.
the last digit to work correctly.
To set Numeric Pager/Voice Event Notification Phone
Number, press:
Number, press:
Add—Option #—43—Up to 26 digits—DONE.
Note
Pressing DONE is required if you enter fewer than 26
digits. The phone number is automatically stored without
pressing DONE if all 26 places are used.
digits. The phone number is automatically stored without
pressing DONE if all 26 places are used.
To delete Numeric Pager/Voice Event Notification Phone
Number, press:
Number, press:
Delete—Option #—43—DONE.
Option 44: Numeric Pager/Voice Event Notification
Phone Mod 3 (Default = 09)
Determines the report content and reporting format when
Option 43: Numeric Pager/Voice Event Notification Phone
Number is programmed. The following table describes the
choices. All entries must be 2 digits.
Option 43: Numeric Pager/Voice Event Notification Phone
Number is programmed. The following table describes the
choices. All entries must be 2 digits.
To set Numeric Pager/Voice Event Notification Phone
Mod 3, press:
Mod 3, press:
Add—Option #—44—08, 09, or 10—DONE.
To reset Numeric Pager/Voice Event Notification Phone
Mod 3 (return to default), press:
Mod 3 (return to default), press:
Delete—Option #—44—DONE.
Phone Mod 3
Setting #
Content
Format
08
Latchkey, No Activity, Phone Test,
Openings, Closings, Fail to Open/
Close, AC Power Restorals/
Failures
Openings, Closings, Fail to Open/
Close, AC Power Restorals/
Failures
Numeric
Pager
Pager
09
Same as setting 8 plus Alarms
Numeric
Pager
Pager
10
Alarms only
Voice Event
Notification
Notification