RM Acquisition LLC 1000FA 用户手册
Document:
TBD
Page:
42
of
42
ENGINEERING
Documentation
Revision:
1.6
Date:
24-May-17
Title:
TND540 Requirement
Proprietary and Confidential
This document contains confidential and property information which belongs to Rand McNally, Inc. This
document may not be copied, reproduced, or transmitted to others in any manner, nor may any use of the
information on this document be made, except for the specific purposes for which it is transmitted to the
recipient without prior written consent of Rand McNally, Inc.
document may not be copied, reproduced, or transmitted to others in any manner, nor may any use of the
information on this document be made, except for the specific purposes for which it is transmitted to the
recipient without prior written consent of Rand McNally, Inc.
7.1.2
Uniformity
Uniformity is determined using the 5-spot method. This consists of measuring the luminance perpendicular to the
screen at 5 specific points (P1, P3, P5, P7, P9) and dividing the highest measurement by the lowest measurement.
This value should be equal to or less than 1.2 as specified herein.
screen at 5 specific points (P1, P3, P5, P7, P9) and dividing the highest measurement by the lowest measurement.
This value should be equal to or less than 1.2 as specified herein.
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
The highest SAR value reported under this standard during product certification for use
at the when properly worn the the body is 0.219W/kg, This device
was tested for typical body-worn operations. To comply with RF exposure requirements,
a minimum separation distance of 0 cm. must be maintained between the user’s body
and the interphone,including the antenna. Third-party belt-clips, holsters and similar accessories
used by this device should not contain any metallic components. Body-worn accessories
that do not meet these requirements may not comply with RF exposure requirements and
should be avoided.
at the when properly worn the the body is 0.219W/kg, This device
was tested for typical body-worn operations. To comply with RF exposure requirements,
a minimum separation distance of 0 cm. must be maintained between the user’s body
and the interphone,including the antenna. Third-party belt-clips, holsters and similar accessories
used by this device should not contain any metallic components. Body-worn accessories
that do not meet these requirements may not comply with RF exposure requirements and
should be avoided.