Elecsys International Corporation 02008400 用户手册
Elecsys Confidential
For Internal Use Only
Rev B – USA / Canada
3
31 March 2016
OEM RESPONSIBILITIES FOR FCC AND INDUSTRY CANADA COMPLIANCE
The 02-0084-00 Modem Module has been certified for integration into products only by OEM integrators
under the following conditions:
1. The antenna(s) must be installed such that a minimum separation distance of 20cm is maintained
between the radiator (antenna) and all persons at all times.
2. The transmitter module must not be co-located or operating in conjunction with any other antenna
or transmitter.
between the radiator (antenna) and all persons at all times.
2. The transmitter module must not be co-located or operating in conjunction with any other antenna
or transmitter.
As long as the two conditions above are met, further transmitter testing will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location
with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid
and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining
a separate FCC and Industry Canada authorization.
The 02-0084-00 Modem Module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and
IC Certification Number are not visible when the module is installed inside another device, then the outside of
the device into which the module is installed must also display a label referring to the enclosed module. In that
case, the final end product must be labeled in a visible area with the following:
OEM integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location
with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid
and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining
a separate FCC and Industry Canada authorization.
The 02-0084-00 Modem Module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and
IC Certification Number are not visible when the module is installed inside another device, then the outside of
the device into which the module is installed must also display a label referring to the enclosed module. In that
case, the final end product must be labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: 2ABOY-02008400”
“Contains Transmitter Module IC: 12222A-02008400”
OR
“Contains FCC ID: 2ABOY-02008400”
“Contains IC: 12222A-02008400”
“Contains Transmitter Module IC: 12222A-02008400”
OR
“Contains FCC ID: 2ABOY-02008400”
“Contains IC: 12222A-02008400”
The OEM of the 02-0084-00 Modem Module must only use the approved antenna(s) listed above, which have
been certified with this module. The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module or change RF related parameters in the user manual of
the end product. This modem module employs RP-SMA antenna connectors to fulfill the unique connector
requirements of §§ 15.203 and 15.212(a)(1)(iv).
The User Manual for the end product must also include the following information in a
prominent location:
prominent location:
FCC and INDUSTRY CANADA NOTICES:
Contains Transmitter Module FCC ID: 2ABOY-02008400
Contains Transmitter Module IC: 12222A-02008400
This device complies with part 15 of the FCC Rules, and Industry Canada’s license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)
Operation is subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la norme RSS Industrie Canada exempt de licence. Son fonctionnement est soumis aux
deux conditions suivantes :
(1)
cet appareil ne peut pas provoquer d’interférences ; et,
(2)
Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
fonctionnement du dispositif.