Elecsys International Corporation 02008410 用户手册
Elecsys Confidential
For Internal Use Only
Rev A – USA / Canada
3
23 August 2018
O
O
O
OEM
EM
EM
EM RESPONSIBILITIES FOR
RESPONSIBILITIES FOR
RESPONSIBILITIES FOR
RESPONSIBILITIES FOR FCC AND INDUSTRY CANADA COMPLIANCE
FCC AND INDUSTRY CANADA COMPLIANCE
FCC AND INDUSTRY CANADA COMPLIANCE
FCC AND INDUSTRY CANADA COMPLIANCE
The 02-0084-10 Modem Module has been certified for integration into products only by OEM integrators
under the following conditions:
1. The antenna(s) must be installed such that a minimum separation distance of 20cm is maintained
between the radiator (antenna) and all persons at all times.
2. The transmitter module must not be co-located or operating in conjunction with any other antenna
or transmitter.
3. The OEM integrator is responsible for ensuring the end-user has no manual instructions to remove
or install module.
between the radiator (antenna) and all persons at all times.
2. The transmitter module must not be co-located or operating in conjunction with any other antenna
or transmitter.
3. The OEM integrator is responsible for ensuring the end-user has no manual instructions to remove
or install module.
As long as the three conditions above are met, further transmitter testing will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE
OEM integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE
IMPORTANT NOTE
IMPORTANT NOTE
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location
with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid
and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining
a separate FCC and Industry Canada authorization.
The separate approval is required for all other operating configurations, including portable configurations with
respect to Part 2.193
with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid
and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining
a separate FCC and Industry Canada authorization.
The separate approval is required for all other operating configurations, including portable configurations with
respect to Part 2.193
(§ 2.193)
and different antenna configurations.
The 02-0084-10 Modem Module is labeled with its own FCC ID, IC Certification Number and the Product
Marking Name (PMN). If the FCC ID, IC Certification Number and Product Marking Name (PMN) are not visible
when the module is installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. In that case, the final end product must be
labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: 2ABOY-02008410”
“Contains Transmitter Module IC: 12222A-02008410”
OR
“Contains FCC ID: 2ABOY-02008410”
“Contains IC: 12222A-02008410”
“Contains Transmitter Module IC: 12222A-02008410”
OR
“Contains FCC ID: 2ABOY-02008410”
“Contains IC: 12222A-02008410”
The OEM of the 02-0084-10 Modem Module must only use the approved antenna(s) listed above, which have
been certified with this module. The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module or change RF related parameters in the user manual of
the end product. This modem module employs RP-SMA antenna connectors to fulfill the unique connector
requirements of §§ 15.203 and 15.212(a)(1)(iv).
The User Manual for the
The User Manual for the
The User Manual for the
The User Manual for the end product
end product
end product
end product must also include the following information in a
must also include the following information in a
must also include the following information in a
must also include the following information in a
prominent location:
prominent location:
prominent location:
prominent location:
FCC and
FCC and
FCC and
FCC and INDUSTRY CANADA NOTICES:
INDUSTRY CANADA NOTICES:
INDUSTRY CANADA NOTICES:
INDUSTRY CANADA NOTICES:
Contains Transmitter Module FCC ID: 2ABOY-02008410
Contains Transmitter Module IC: 12222A-02008410
Contains Transmitter Module IC: 12222A-02008410