GENIUS TOY TAIWAN CO. LTD 7447-W85-B 用户手册
2
push
pull
push
pull
switch
buon
channel
switch
socket
ON
OFF
x4
Here are a few tips for assembling
and using the models. Read them
carefully before starting.
A. Place the tires on the
wheels
wheels
Place a tire over each of the four
wheels before you build the first
model.
B. Batteries in RF remote
control unit
control unit
Open the baery compartment by
pushing on the tab on the back of
the RF receiver unit and lifting the
back panel up. Insert two AA
baeries, paying aention to the
polarity indicated in the
compartment and on the
baeries. Close the compartment
again.
C. Batteries in RF receiver
Open the baery compartment by
pushing on the tab on the boom
of the RF baery box. Insert six
AA baeries, paying aention to
the polarity indicated in the
compartment and on the
baeries. Close the compartment
again.
D. Using the RF remote
control
control
To control a model, turn on both
the motor unit and the remote
control unit by moving their
switches from the “off” position
(O) to the “on” position (–). The
lights will flash on the RF remote
control unit and receiver while
they establish a connection. Once
a connection is established the
lights on the receiver will turn off
and the light on the remote
control unit will be solid. If you
are using multiple RF remote
control units and baery boxes in
the same area, set the remote
control units to different channels
and then establish connections to
the baery.
The left side of the RC unit
controls the socket on the left
side of the baery box. The right
side of the RC unit controls the
socket on the right side of the
baery box.
If you want your model to
move in the opposite direction
when you press one of the RC unit
buons, you can simply rotate
the direction of the plug in the
socket 180 degrees.
SWITCH
POWER
rounded
flat
GENERAL BUILDING TIPS
ANCHOR PINS AND CONNECTORS
Take a careful look at the different assembly
components. Red anchor pins, blue anchor pins,
joint pins, and shaft plugs all look prey similar
at first glance. When you assemble the models, it’s
important to use the right ones. The blue anchor pins
are shorter than the red ones.
components. Red anchor pins, blue anchor pins,
joint pins, and shaft plugs all look prey similar
at first glance. When you assemble the models, it’s
important to use the right ones. The blue anchor pins
are shorter than the red ones.
CONNECTING
FRAMES AND RODS
FRAMES AND RODS
Use the anchor pins to connect
frames and rods.
frames and rods.
AXLES
The building system contains
axles (also called shafts) of
various lengths. When assembling
the model, always be sure that
you’re using the right one.
axles (also called shafts) of
various lengths. When assembling
the model, always be sure that
you’re using the right one.
ANCHOR PIN LEVER
When you want to take your model apart
again, you will need the anchor pin lever.
Use the narrow end of the lever
to remove the
anchor pins. You
can use the wide
end to pry out
shaft plugs.
anchor pins. You
can use the wide
end to pry out
shaft plugs.
PULLEYS AND GEARS
If pulleys or gears are mounted too tightly against
other components, they can be hard to turn. If you
leave a gap of about 1 mm between the gear or
pulley and an adjacent component, it will turn easily.
In some of the models, a washer is used to ensure this
kind of spacing. (There are no gears included in this
kit.)
other components, they can be hard to turn. If you
leave a gap of about 1 mm between the gear or
pulley and an adjacent component, it will turn easily.
In some of the models, a washer is used to ensure this
kind of spacing. (There are no gears included in this
kit.)
A
B
› › › TIPS AND TRICKS
2 x AA
6 x AA
C
D