Develco Products MOSZB140 Test Setup Photos
eng
a.
b.
c.
d.
e.
f.
g.
h.
i.
Connecting
1. When batteries are inserted, the Motion
Sensor Mini will automatically start
searching (up to 15 minutes) for a Zigbee
network to join.
searching (up to 15 minutes) for a Zigbee
network to join.
2. Make sure that the Zigbee network is open
for joining devices and will accept the
Motion Sensor Mini.
Motion Sensor Mini.
3. While the sensor is searching for a Zigbee
network to join, the LED flashes red.
4. When the sensor is connected to a network,
it wil stop flashing.
STAND
1. If you have a sensor with
a plastic stand included,
you can insert the stand
in the opening on the
back of the sensor as
shown on the drawing.
you can insert the stand
in the opening on the
back of the sensor as
shown on the drawing.
2. Place the standing sensor
on the shelf or on a desk.
MOUNTING FLAT ON CEILING OR WALL
1. Open the casing, and use the sensor part
with oval holes to mark the screw holes on
a ceiling or a wall.
a ceiling or a wall.
• Place the sensor free of curtains and other
obstacles.
• Avoid placing the Motion Sensor Mini close
to a heating/cooling source.
• Avoid placing the Motion Sensor Mini in
direct sunlight or bright light.
• Place the sensor indoors at a temperature
between 0-50°C.
• Its angle of detection from above, the sides,
and below must be 45°.
• Place the Motion Sensor Mini in a location
with a clear view of the monitored area and
the windows.
the windows.
• The distance from the sensor to a fireplace
or a stove must be at least four meters.
• The Motion Sensor Mini must be reachable
for battery testing and maintenance.
Product description
The compact Motion Sensor Mini allows the
user to detect occupancy. With the Motion
Sensor Mini, the user can set the light to
turn on and off as people come and go. The
motion sensor is PIR based and is able to
sense movement up to 9 meters from the
sensor.
user to detect occupancy. With the Motion
Sensor Mini, the user can set the light to
turn on and off as people come and go. The
motion sensor is PIR based and is able to
sense movement up to 9 meters from the
sensor.
Motion Sensor Mini includes two logical
outputs – one with high sensitivity for
occupancy and one with a lower sensitivity
for alarm.
outputs – one with high sensitivity for
occupancy and one with a lower sensitivity
for alarm.
Motion Sensor Mini
Version 1.1
INSTALLATION MANUAL
Placement
CORNER OR CEILING MOUNTING WITH
BRACKET
BRACKET
1. If you have a sensor with a bracket included,
you can mount the sensor with this bracket
in a corner or on the ceiling.
in a corner or on the ceiling.
2. Use the bracket to mark the screw holes on
the two walls in the corner of the room or
on the ceiling.
on the ceiling.
3. Use the two screws in the bag marked “A”
to install the bracket in the marked place.
3. Alternatively, you can use the adhesive
tape from bag “A” to mount the sensor.
4. Insert batteries and make sure that the
battery polarity is correct (+/-).
5. Close the casing of the sensor.
4. Alternatively, you can use the adhesive
tape from bag “A” to mount the bracket.
5. Open the casing of the sensor.
6. Place the part with oval holes against the
already mounted bracket.
7. Take two screws from the bag marked “B”.
Mount one screw through each oval hole
and into two holes on the bracket.
and into two holes on the bracket.
8. Insert batteries and make sure that the
battery polarity is correct (+/-).
9. Close the casing of the sensor.
2. Mount the sensor on the wall or the ceiling
by installing one screw from the bag
marked “A” through each oval hole.
marked “A” through each oval hole.
Mounting
Modes
SEARCHING GATEWAY MODE
Red LED light is flashing every second (up to
15 minutes).
15 minutes).
ALARM TESTING MODE
The motion sensor will automatically flash
green every time movement is detected by
the Intruder Alarm System (IAS), no matter if
the alarm system is activated or deactivated.
The green flashes can help you determine
if the placement of the sensor is suitable for
alarm purposes.
green every time movement is detected by
the Intruder Alarm System (IAS), no matter if
the alarm system is activated or deactivated.
The green flashes can help you determine
if the placement of the sensor is suitable for
alarm purposes.
LOW BATTERY MODE
The device will flash red twice every minut
when the battery is low.
when the battery is low.