BagelLabs co. Ltd. BAGEL001 用户手册

Dimensions

80 x 80 x 30mm (L x W x H)

Weight

118g

Voltage

Input: 5V DC / Driving: 3.3V DC

Display

0.96” OLED (128x64)

Storage Capacity

32MB

Battery

Built-in rechargeable Li-Po (500mAh, 3.7V DC)

Wireless Connectivity

Bluetooth 4.0 BLE (Only)

Laser

Voltage: 3V DC / Current: <25mA, 

Wavelength

660nm Red / Class: 2

Materials

Polycarbonate Casing / Dyneema String

Compatible OS

Android, iOS

Measurement Range

String : 0-300cm (0-9’ 10’’)

Wheel: 0-999cm (0-32’ 9’’)

Remote: 30cm - 500cm (1’-16’ 4’’)

Bluetooth Frequency

2.4GHz

Turn the device on by pressing the      

Power Button

 

Select a measurement mode (String/Wheel/Remote).

Press the      

Mode/Settings button

  

to enter mode menu.  

Press the      

Mode/Settings button

 

 again to switch between modes.

String Mode:  Pull out the       

hook/string.

Wheel Mode:  Roll the       

wheel

  

in the direction guided by the wheel  guide laser.

Remote Mode:  Point the       

ultrasonic sensor

 at the target of measurement.

→ 

→ 

Press and hold the      

save button   

to view logs .

Use the      

wheel

 or      

MODE/SETTINGS BUTTON  

to scroll through saved measurements.

To delete a measurement, press the      

save button

 and select “Yes”.

To delete all measurements, hold the      

save button

 and select “Yes”.

You can leave the menu by clicking the      

cancel/bluetooth button 

.

Factory default time zone may differ from yours. You can sync Bagel's time zone 

to yours by pairing the device with a smartphone (Section 03).

Press the      

save button

  once to save the measurement shown on the digital display.

On the “Voice Memo?” screen, use the     

WHEEL

 

or     

MODE/SETTINGS BUTTON 

to select “Yes” in order to record a voice memo.
Alternatively, select “No” to save without a voice memo.

Press and hold the      

cancel/bluetooth button

 to enter pairing mode on Bagel.

Download and install the Bagel Labs mobile app from http://www.bagel-labs.com. 

 “Pairing…” should show up on the digital display.
On the mobile app, enter the settings menu by clicking the        button.

Click on [Bluetooth Pairing] to start the scan for Bagel.

 

Press and hold the      mode/setting button   to enter settings menu.

Scroll through menus using the       wheel or        mode/setting button  to highlight [Units].

Press the      save button  to enter. 

Use the wheel or        mode/setting button  to select [cm], [in], or [mm].

Press the      save button to save and exit. Or, press the      cancel/bluetooth button  to return 

to settings menu without saving.

Press and hold the      mode/setting button  to enter settings menu.

Scroll through menus to highlight [Laser] and enter.

Select [On] or [Off].

Press the      save button to save and exit. Or, press the      cancel/bluetooth button  to return 

to settings menu without saving.

Setting Inside/Outside Measurements
By default, Bagel’s measurements start from 0 (Offset setting OFF). If you want to make inside  

measurements, e.g. length of window sill, you can set Bagel to offset mode (Offset setting ON). 

Then, Bagel’s measurements will start from 8cm (3.15”), which is the diameter of Bagel. 

Press and hold the      mode/setting button to enter settings menu.

Scroll through menus to highlight [Offset] and enter.
Select [On] or [Off].
Press the      save button  to save and exit. Or, press the      cancel/bluetooth button  to return 

to return to settings menu without saving.

Charging the battery before use is recommended but not required.

Bagel ships pre-charged but initial charge will vary.

To charge Bagel, simply connect the included micro USB cable to the      

charging port.

The     

LED STATUS INDICATOR

 should turn red while charging. 

Bagel will display “Low battery” at 5%.

Full discharge of the battery can reset the Real Time Clock (RTC) and cause time 

inaccuracy. To resynchronize time, pair Bagel with its mobile app.

This device can be operated while charging.

Note: The micro USB port is for charging purpose only and does not support data transfer.