Mc Crypt ME502FP Mixer 305694 数据表
产品代码
305694
35
8. Connection
Ensure that the mains adapter of the device is disconnected and all TRIM, channel and MAIN
MIX controls are set to the minimum value before the device is connected or any connection is
changed.
MIX controls are set to the minimum value before the device is connected or any connection is
changed.
Make sure that all electrical connections and connection cables between the different devices
and any extension cables comply with the regulations and the operating instructions.
and any extension cables comply with the regulations and the operating instructions.
Only connect audio outputs with suitable shielded connection cables. Use of other cables
might cause interference.
might cause interference.
To avoid distortions or mismatches that could damage the device, only connect devices with
the same connection type.
the same connection type.
For this, observe also the connection information in the section “Technical Data”.
Cables are important connection links in the system. Therefore, use high-quality step-protect-
ed cables with high-quality plugs. Do not place the mixer’s in/output cables directly adjacent
to mains cables. If required, cross the cables at a 90-degree angle to keep the danger if inter-
ference as low as possible.
ed cables with high-quality plugs. Do not place the mixer’s in/output cables directly adjacent
to mains cables. If required, cross the cables at a 90-degree angle to keep the danger if inter-
ference as low as possible.
Last, connect the included mains adapter with the device. For this, connect the 3-pin low-voltage plug to the mixer
mains adapter socket. Then secure the plug with the thumb screw. Only then plug the mains adapter of the mains
cable into a 230V AC / 50Hz household mains socket. The device is now operational.
mains adapter socket. Then secure the plug with the thumb screw. Only then plug the mains adapter of the mains
cable into a 230V AC / 50Hz household mains socket. The device is now operational.
9. Socket Assignment
Zugentlastung
Schaft/sleeve
Spitze/tip
Schaft/sleeve
Spitze/tip
Masse/Schirmung
Signal
Bei unsymmetrischen Betrieb müssen PIN1 und PIN3 verbunden werden
Ring und Schaft des Stereoklinkensteckers sind zu brücken, wenn eine Ver-
bindung zwischen symmetrischen zu unsymmetrischen Anschluss erfolgt.
bindung zwischen symmetrischen zu unsymmetrischen Anschluss erfolgt.
6,3mm Kopfhörerklinkenstecker
Zugentlastung
Schaft/sleeve
Spitze/tip
Schaft/sleeve
Spitze/tip
Masse/Schirmung
Linkes Signal
Ring/ring
Rechtes Signal
Ring/ring
Zugentlastung
Schaft/sleeve
Spitze/tip
Schaft/sleeve
Spitze/tip
Masse/Schirmung
Plus (+/heiß)
Ring/ring
Minus (-/kalt)
Ring/ring
6,3mm Stereoklinkenstecker
Betrieb symmetrisch (balanced)
6,3mm Monoklinkenstecker
Betrieb unsymmetrisch (unbalanced)
Betrieb unsymmetrisch (unbalanced)
XLR Anschlussbelegung symmetrisch (balanced)
1=Masse / Schirmung
2=Plus (+/heiß)
3=Minus (-/kalt)
2=Plus (+/heiß)
3=Minus (-/kalt)
1
2
3
1
2
3
Input
Output
6.3 mm mono jack plug unsymmetrical
operation (unbalanced)
operation (unbalanced)
Stress relief
Shaft/sleeve
Shaft/sleeve
Earth/Shield
Earth/Shield
Peak/tip
Signal
Signal
Peak/tip
XLR connection assignment symmetric (balanced)
1=Earth/Shield
2=Plus (hot)
3=Minus (cold)
2=Plus (hot)
3=Minus (cold)
For asymmetric operation, PIN1 and PIN3 must be connected.
6.3 mm stereo jack plug symmetrical
operation (balanced)
operation (balanced)
Stress relief
Shaft/sleeve
Shaft/sleeve
Earth/Shield
Earth/Shield
Peak/tip
Plus (+/hot)
Plus (+/hot)
Ring/ring
Ring/ring
Minus (-/cold)
Minus (-/cold)
Ring and shaft of the stereo jack plug must be bridged if a connection is made
between the symmetrical and asymmetrical connection.
between the symmetrical and asymmetrical connection.
Peak/tip
6.3 mm headphone plug socket
Stress relief
Shaft/sleeve
Shaft/sleeve
Earth/Shield
Earth/Shield
Peak/tip
Left signal
Left signal
Ring/ring
Right signal
Right signal
Ring/ring
Peak/tip