Linear Technology LTC2188: 16-bit 20Msps Dual ADC, DDR LVDS Outputs, 5-140MHz, req DC890, LVDS_XFMR and DC1075 DC1620A-S DC1620A-S 数据表

产品代码

DC1620A-S

2188f

LTC2188

PINS THAT ARE THE SAME FOR ALL DIGITAL

OUTPUT MODES
V

(Pins 1, 16, 17, 64): Analog Power Supply, 1.7V to

1.9V. Bypass to ground with 0.1µF ceramic capacitors.

Adjacent pins can share a bypass capacitor.
V

CM1

(Pin 2): Common Mode Bias Output, nominally equal

to V

/2. V

CM1

should be used to bias the common mode

of the analog inputs to channel 1. Bypass to ground with

a 0.1µF ceramic capacitor.
GND (Pins 3, 6, 14): ADC Power Ground.
A

IN1

(Pin 4): Channel 1 Positive Differential Analog Input.

IN1

–

(Pin 5): Channel 1 Negative Differential Analog Input.

REFH (Pins 7, 9): ADC High Reference. See the Applica-

tions Information section for recommended bypassing

circuits for REFH and REFL.
REFL (Pins 8, 10): ADC Low Reference. See the Applica-

tions Information section for recommended bypassing

circuits for REFH and REFL.
PAR/SER (Pin 11): Programming mode selection pin. Con-

nect to ground to enable the serial programming mode.

CS, SCK, SDI, SDO become a serial interface that control

the A/D operating modes. Connect to V

to enable the

parallel programming mode where CS, SCK, SDI, SDO

become parallel logic inputs that control a reduced set of

the A/D operating modes. PAR/SER should be connected

directly to ground or V

and not be driven by a logic signal.

IN2

(Pin 12): Channel 2 Positive Differential Analog Input.

IN2

–

(Pin 13): Channel 2 Negative Differential Analog Input.

CM2

(Pin 15): Common Mode Bias Output, nominally

equal to V

/2. V

CM2

should be used to bias the common

mode of the analog inputs to channel 2. Bypass to ground

with a 0.1µF ceramic capacitor.
ENC

(Pin 18): Encode Input. Conversion starts on the

rising edge.
ENC

–

(Pin 19): Encode Complement Input. Conversion

starts on the falling edge. Tie to GND for single-ended

encode mode.

CS (Pin 20): In serial programming mode, (PAR/SER =

0V), CS is the Serial Interface Chip Select Input. When CS

is low, SCK is enabled for shifting data on SDI into the

mode control registers. In the parallel programming mode

(PAR/SER = V

), CS controls the clock duty cycle stabilizer

(See Table 2). CS can be driven with 1.8V to 3.3V logic.
SCK (Pin 21): In serial programming mode, (PAR/SER =

0V), SCK is the Serial Interface Clock Input. In the parallel

programming mode (PAR/SER = V

), SCK controls the

digital output mode. (See Table 2). SCK can be driven with

1.8V to 3.3V logic.
SDI (Pin 22): In serial programming mode, (PAR/SER =

0V), SDI is the Serial Interface Data Input. Data on SDI

is clocked into the mode control registers on the rising

edge of SCK. In the parallel programming mode (PAR/

SER = V

), SDI can be used together with SDO to power

down the part (see Table 2). SDI can be driven with 1.8V

to 3.3V logic.
OGND (Pin 41): Output Driver Ground. Must be shorted

to the ground plane by a very low inductance path. Use

multiple vias close to the pin.
OV

(Pin 42): Output Driver Supply. Bypass to ground

with a 0.1µF ceramic capacitor.
SDO (Pin 61): In serial programming mode, (PAR/SER

= 0V), SDO is the optional Serial Interface Data Output.

Data on SDO is read back from the mode control regis-

ters and can be latched on the falling edge of SCK. SDO

is an open-drain NMOS output that requires an external

2k pull-up resistor to 1.8V – 3.3V. If read back from the

mode control registers is not needed, the pull-up resistor

is not necessary and SDO can be left unconnected. In the

parallel programming mode (PAR/SER = V

), SDO can

be used together with SDI to power down the part (see

Table 2). When used as an input, SDO can be driven with

1.8V to 3.3V logic through a 1k series resistor.
V

REF

(Pin 62): Reference Voltage Output. Bypass to

ground with a 2.2µF ceramic capacitor. The output voltage

is nominally 1.25V.

pin FuncTions