Reely RC model speedboat ARR 750 mm 275440 数据表
产品代码
275440
40
d) Range Test
Before first use, the drive battery and any rechargeable batteries used in the transmitter have to be charged as
instructed by the manufacturer.
instructed by the manufacturer.
Then perform a range test of the remote control system. Switch on the remote control and then the receiver.
Check the range of your remote control with a helper, by having the helper hold the operational model ship and you
moving away from the model. Control must work interference-free at least at a distance of
50 metres.
moving away from the model. Control must work interference-free at least at a distance of
50 metres.
e) The First Trip
The speed controller control electronics only permit the model to drive forwards. When manoeuvring,
observe that you do not have a reverse gear as in a model ship, for example.
observe that you do not have a reverse gear as in a model ship, for example.
Operation is only permissible with the hull deck applied. Otherwise, splashing water may enter the boat
and destroy the remote control and drive parts. Loss of guarantee/warranty!
and destroy the remote control and drive parts. Loss of guarantee/warranty!
The model’s speed controller has an undervoltage recognition for the drive battery integrated for safety-technical
reasons. If the battery switches off to prevent harmful deep discharge of the drive battery, the model would float and be
no longer controllable, and might be lost. Therefore, interrupt operation in time, but no later than after 5 to 8 minutes
(depending on the operating style and battery used), to reach the shore under own power and to avoid deep discharge
of the drive battery.
reasons. If the battery switches off to prevent harmful deep discharge of the drive battery, the model would float and be
no longer controllable, and might be lost. Therefore, interrupt operation in time, but no later than after 5 to 8 minutes
(depending on the operating style and battery used), to reach the shore under own power and to avoid deep discharge
of the drive battery.
Trips under detriment conditions such as strong wind and strong waves are not permissible and may cause loss of the
model.
model.
If you notice any unusual noise or sudden rotating or model speed loss during operation, terminate operation at once
and find the reason. In most cases, seaweed or something similar will have become tangled in the ship’s propeller,
which may impair or render the drive near ineffective. If operation is continued, this may destroy drive components.
Loss of guarantee/warranty!
and find the reason. In most cases, seaweed or something similar will have become tangled in the ship’s propeller,
which may impair or render the drive near ineffective. If operation is continued, this may destroy drive components.
Loss of guarantee/warranty!
Check the water cooling function before any voyage. For this, you may use a small hose to blow air into the water
cooling inlet (see figure 8, item 3). The air (or water in driving operation) must come out of the outlet again (figure 8,
item 4). Never drive with a water cooling that is clogged or non-functional because of bent hoses. The motor and/or
speed controller may overheat and take damage. Loss of guarantee/warranty!
cooling inlet (see figure 8, item 3). The air (or water in driving operation) must come out of the outlet again (figure 8,
item 4). Never drive with a water cooling that is clogged or non-functional because of bent hoses. The motor and/or
speed controller may overheat and take damage. Loss of guarantee/warranty!
Carefully and horizontally put the model on the water. Observe that the ship’s propeller is turning freely and does not
touch the ground.
touch the ground.
Carefully pull the throttle lever towards the handle. The model starts to drive forward. Turning the remote control
steering wheel to the left or right will cause your model to turn in the respective direction.
steering wheel to the left or right will cause your model to turn in the respective direction.
Driving time is approx. 5 to 8 minutes, depending on driving style. Terminate the trip in time and return to the shore.
Open the hull deck, unplug the drive battery, switch off the transmitter and check if any water has entered the model.
Ingressing water must be removed at once. Observe that the water does not enter the remote control or drive parts
during emptying.
Open the hull deck, unplug the drive battery, switch off the transmitter and check if any water has entered the model.
Ingressing water must be removed at once. Observe that the water does not enter the remote control or drive parts
during emptying.