Renkforce LED wall light 10.5 W Warm white HY0002UP-4 Silver-grey HY0002UP-4 数据表

The product is designated for illuminating indoor and outdoor areas. It is intended for 

wall mounting.
It is essential that you follow all safety instructions and other information in these 

operating instructions! 
Any other than the intended use described above might result in product damage and 

furthermore cause hazards such as electric shock. The product as a whole must not 

be modified or altered!
This product complies with the statutory national and European requirements. All 

company names and product names are trademarks of their respective owners. All 

rights reserved.

•  LED wall lamp
•  Installation materials (screws, screw anchors)
•  Operating instructions

  The symbol with the flash in a triangle indicates a risk to your health, e.g. 

from electric shock.

  This symbol informs you about specific risks when handling, operating or 

using the product. 

  The “arrow” symbol indicates special remarks and notes for operation.

  The light is not dimmable.

  Follow the user manual!

 

•  Due to safety and approval concerns (CE) the product must not be modi-

fied and/or altered without authorization.

 

•  The LED wall lamp is not a toy; keep away from children! There is a risk of 

lethal electric shock! Install the LED wall lamp out of reach of children.

 

•  The LED wall lamp must only be operated via AC mains voltage (see chap-

ter “Technical Data”). Never attempt to operate the product with other 

voltage, as this might damage the product.

 

•  The LED lamp features a protection class I design; the protective ground 

conductor must be connected. 

 

  If there is no mains cable with protective ground conductor available at 

the place of installation, the LED wall lamp must not be connected/opera-

ted there. In this case, install a new mains cable with protective ground 

conductor.

 

  On the installation side, an all-pole disconnecting device from the mains 

voltage must be installed (i.e. residual current operated circuit breaker).

 

•  The LED wall lamp features a class IP44 construction and may hence be 

installed and operated indoors and outdoors.

 

  Choose the correct position when installing the product (see chapter “In-

stallation and connection”) as otherwise there is a risk of lethal electric 

shock!

 

•  The LED wall lamp must not be operated with a dimmer.

 

•  Do not install or use the LED wall lamp in rooms or under adverse environ-

mental conditions, where combustible gas, vapors or dusts are or could 

be present! There is a risk of explosion!

 

•  The LED wall lamp is only intended for fixed installation. Never install the 

LED wall lamp in cars.

 

•  Do not hang or attach any objects (e.g. decorations) on or to the LED wall 

lamp.

 

•  Protect the LED wall lamp from extreme temperatures, strong vibrations or 

strong mechanical stress.

 

•  If a safe operation can no longer be guaranteed, the LED wall lamp must 

be decommissioned and be secured against accidental use. Have the LED 

wall lamp then checked by an expert.

 

  Safe operation is no longer guaranteed when:

 

-  the LED wall lamp shows visible damage 

 

-  the LED wall lamp does not work correctly or at all (flickering light, esca-

ping smoke or burnt smell, audible cracking noise, discoloration of the 

LED wall lamp or adjacent surfaces).

 

-  the LED wall lamp was stored under inappropriate conditions 

 

-  the product was exposed to rough handling during transport.

 

•  Do not leave packaging material unattended, as children could use it as a 

toy creating hazardous situations.

 

•  For installations in industrial facilities, follow the accident prevention re-

gulations for electrical systems and equipment of the government safety 

organization or the corresponding authority for your country.

 

•  If you have any further questions that have not been considered in these 

operating instructions, please contact us or any other expert.

  Please observe all “Safety instructions”!

•  Install the LED wall lamp on a stable surface only. Depending on the surface, use 

suitable screws and screw anchors. 

•  Within the sub-distribution of the installation site, the LED wall lamp must be secu-

red with a 10/16A fuse, in front of which a residual current circuit breaker must be 

installed.

•  Make sure the mains voltage is disconnected when installing the LED wall lamp. It 

is not sufficient to turn off the light switch!

  Disconnect the mains cable at all poles from the mains supply by removing the ap-

propriate circuit fuse or switching off the circuit breaker. Then switch off the appro-

priate circuit breaker.

  Secure them against unauthorized restart, e.g. by installing a warning sign.
•  Use a suitable measurement device to check the mains cable for absence of volta-

ge.