Waterford Appliances EMERALD E63-NG1 用户手册
18
Waterford E63-1 EMERALD Freestanding Gas Stove
MAINTENANCE
REMOVING VALVE
If your valve requires maintenance or replace-
ment, use the following instructions:
ment, use the following instructions:
Note: Always close off the gas supply
before removing the valve.
1) If optional fan is installed, disconnect pow-
er source to stove.
2) Remove access panel.
FAN MAINTENANCE
If your fan requires maintenance or replace-
ment, access to the fan is through the plate on
the rear wall of the firebox.
ment, access to the fan is through the plate on
the rear wall of the firebox.
IMPORTANT
Disconnect power supply
before servicing
NOTE: the unit MUST NOT be operated
without the fan access panel se-
curely in place and correctly sealed.
curely in place and correctly sealed.
IMPORTANT: These fans collect a
lot of dust from within your home.
Ensure you maintain these fan mo-
tors on a regular basis by vacuum-
ing out the fan squirrel cages, around
the motor, and around the grills on
the back of the stove.
lot of dust from within your home.
Ensure you maintain these fan mo-
tors on a regular basis by vacuum-
ing out the fan squirrel cages, around
the motor, and around the grills on
the back of the stove.
Replacement Part
# 940-087
Emerald Glass
WARNING: Do not operate appli-
ance with glass panels removed,
cracked or broken. Replacement of
the glass should be done by a li-
censed or qualified service person.
ance with glass panels removed,
cracked or broken. Replacement of
the glass should be done by a li-
censed or qualified service person.
Note: Wearing gloves will protect your
hands while handling glass.
REPLACING THE
GASKET
The Emerald has 3/8" fiberglass gasket in the
front door. Should it ever need replacement, use
only the proper replacement gasket that is
available from your Waterford dealer. To re-
place the gasket, follow this procedure.
front door. Should it ever need replacement, use
only the proper replacement gasket that is
available from your Waterford dealer. To re-
place the gasket, follow this procedure.
1) Open the front door (see instructions above
in Glass Replacement 1)).
2) Remove the existing gasket and clean its
channel with a scraper or wire brush.
3) Lay a thin bead of gasket cement the entire
length of the channel.
4) Lay the gasket in the channel with sufficient
pressure that it stays in place. Trim the
excess from the end of the gasket so that
it butts snugly against the other end without
leaving a gap.
excess from the end of the gasket so that
it butts snugly against the other end without
leaving a gap.
5) Close the door and apply firm pressure to
seat the gasket evenly throughout.
WARNING:
Electrical Grounding Instructions
This appliance is equipped with a
three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
To replace fan: See the fan installation
instructions on page 7 and reverse the
steps.
instructions on page 7 and reverse the
steps.
3) Disconnect gas line to stove.
4) Disconnect 3/8" NPT pipe from 90
o
elbow on
valve.
5 ) Disconnect the two (2) switch wires from
valve.
6) Disconnect piezo wire.
7) Open the front door. Open the right side
door and there is a cutout in the heat shield
through which can be seen a wing nut
threaded on to a stud attached to the front
door. Loosen this nut by turning it counter-
clockwise.
through which can be seen a wing nut
threaded on to a stud attached to the front
door. Loosen this nut by turning it counter-
clockwise.
8) Carefully remove the logs, embers and
rockwool.
9) Remove burner. See diagram below.
Note: Use a magnetic type screwdriver
if possible.