Wilson Electronics 271245 用户手册
Wilson
®
Electronics, Inc.
Phone: 866-294-1660
www.wilsonelectronics.com
Fax: 435-656-2432
Part #110435 AIG MW 044 / 06.05.08
Amplifi er Specifi cations
Dual Band
800/1900 MHz Specifi cations
Model Number / Part Number
271245 / 801201
Connectors
FME-Male
Impedance (input/output)
50 ohms
Dimensions
5.6 x 3.6 x 1.7 inch or 14.2 x 9.1 x 4.4 cm
Weight
1.44 lbs or 0.65 kg
Frequency
824-894 MHz / 1850-1990 MHz
1
Passband Gain (nominal)
800 MHz
50 dB
1900 MHz
60 dB
2
20 dB Bandwidth (nominal)
800 MHz (uplink/downlink)
53.5 MHz / 47.7 MHz
1900 MHz (uplink/downlink)
86 MHz / 83 MHz
Power output for single cell phone (uplink)
800 MHz
1900 MHz
CDMA
+30.9 dBm
+30.5 dBm
GSM
+30.0 dBm
+29.7 dBm
EDGE
+30.4 dBm
+30.3 dBm
AMPS
+30.2 dBm
3
Power output (uplink) for multiple
cell phones:
Number of
cell phones
Maximum Power
800 MHz
1900 MHz
2
+25.0 dBm
+24.7 dBm
3
+21.5 dBm
+21.2 dBm
4
+19.0 dBm
+18.7 dBm
5
+17.0 dBm
+16.7 dBm
6
+15.5 dBm
+15.2 dBm
Power output for single received channel
(downlink)
(downlink)
800 MHz
1900 MHz
CDMA
+10.0 dBm
+9.9 dBm
GSM
+11.0 dBm
+9.9 dBm
EDGE
+10.9 dBm
+9.6 dBm
AMPS
+10.3 dBm
4
Power output for multiple received
channels (downlink). The maximum
power is reduced by the number of
channels:
power is reduced by the number of
channels:
Number of
channels
Maximum Power
800 MHz
1900 MHz
2
-11.6 dBm
-3.1 dBm
3
-15.1 dBm
-6.6 dBm
4
-17.6 dBm
-9.1 dBm
5
-19.6 dBm
-11.1 dBm
6
-21.1 dBm
-12.6 dBm
Noise Figure (typical)
3 dB nominal
Isolation
> 90 dB
Power Requirements
Amplifi er Usage
Amplifi er Usage
6 V, .5 A - 1.5 A (subject to uplink power)
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
Average gains are: 37 dB (800 MHz uplink & downlink) 45 dB (1900 MHz uplink & downlink)
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplifi cation is 20 dB
1. Nominal gain is the maximum gain at any frequency in the passband.
Average gains are: 37 dB (800 MHz uplink & downlink) 45 dB (1900 MHz uplink & downlink)
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplifi cation is 20 dB
lower than the passband amplifi cation. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can
cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device.
cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.