Universal Security Instruments MICN109 数据表
Page 2 of 3
AUDIBLE & VISUAL SIGNALS
CONDITION /
RECOMMENDATION
HORN
POWER
GREEN LED
SMOKE
RED LED
GAS
BLUE LED
CO
RED LED
1 beep,
2 second pause,
repeat
Turns Off when
the 1 beep
starts
Off
Off
Off
Condition: Non-originating GAS Alarm.
Recommendation: An interconnected GAS
alarm has sensed GAS, causing all
interconnected units to sound. If hazard is
identified, take all precautions if an alarm
sounds by calling an Emergency Service and
getting out of the home.
Recommendation: An interconnected GAS
alarm has sensed GAS, causing all
interconnected units to sound. If hazard is
identified, take all precautions if an alarm
sounds by calling an Emergency Service and
getting out of the home.
Horn sounds when
no hazard is
present
Turns Off when
the beeps start
Off or Blinks
On approx.
once every
once every
second
Off or Blinks
On in sync
with the 1
beep
Off or Blinks
On in sync
with 4 beeps
Condition: Nuisance Alarm.
Recommendation: If there is no hazard
present, verify the alarm is mounted in the
correct location (see User’s Manual). Reset
alarm as instructed below.
Recommendation: If there is no hazard
present, verify the alarm is mounted in the
correct location (see User’s Manual). Reset
alarm as instructed below.
3 beeps,
2 second pause,
repeat
Turns Off when
the 3 beeps
start
Blinks On
approx. once
every second
Off
Off
Condition: Smoke alarm when cause of
alarm is known and poses no threat.
Recommendation: The smoke alarm Silence
Feature can be activated by pressing and
releasing the Test/Silence button on the
initiating alarm while in alarm condition.
Silence mode will last for approx. 8-12
minutes (with the red LED blinking on approx.
every 10 seconds).
alarm is known and poses no threat.
Recommendation: The smoke alarm Silence
Feature can be activated by pressing and
releasing the Test/Silence button on the
initiating alarm while in alarm condition.
Silence mode will last for approx. 8-12
minutes (with the red LED blinking on approx.
every 10 seconds).
4 beeps,
5 second pause,
repeat
Turns Off when
the 4 beeps
start
Off
Off
Blinks On in
sync with 4
beeps
Condition: CO alarm when cause of alarm is
known and poses no threat.
Recommendation: The CO alarm Silence
Feature can be activated by pressing and
releasing the Test/CO Silence button on the
initiating alarm while in alarm condition. The
alarm will remain silent for approx. 5 minutes
(with the red LED blinking on approx. every
10 seconds), depending on the level of CO
detected. If CO levels drop below alarm
levels, the alarm will remain silent and return
to normal operation. If CO levels remain
constant or increase, this indicates a
potentially dangerous situation and the horn
will sound again. Ventilate area.
known and poses no threat.
Recommendation: The CO alarm Silence
Feature can be activated by pressing and
releasing the Test/CO Silence button on the
initiating alarm while in alarm condition. The
alarm will remain silent for approx. 5 minutes
(with the red LED blinking on approx. every
10 seconds), depending on the level of CO
detected. If CO levels drop below alarm
levels, the alarm will remain silent and return
to normal operation. If CO levels remain
constant or increase, this indicates a
potentially dangerous situation and the horn
will sound again. Ventilate area.
Silent (alarmed
previously)
On and Blinks
Off approx.
every 20
seconds
Off or Blinks
On approx.
every 5
seconds until
reset
Off or Blinks
On approx.
every 5
seconds until
reset
Off or Blinks
On approx.
every 5
seconds
until reset
Condition: Previous alarm condition at
unidentified source.
Recommendation: QUICK FIND® Alarm
Origination - In an interconnected system, it is
difficult to determine which alarm initiated the
alarms to sound. The QUICK FIND® feature
will immediately allow you to locate the
originating alarm (once the alarms have
stopped sounding). To initiate QUICK FIND®,
press the Test/Silence button on any alarm.
After releasing the button, the test sequence
will sound and then stop. Then, the originating
alarm will continue to sound for approx. 50
seconds. In a non-interconnected installation,
it is necessary to test each alarm to determine
the originating alarm. Reset the originating
alarm.
unidentified source.
Recommendation: QUICK FIND® Alarm
Origination - In an interconnected system, it is
difficult to determine which alarm initiated the
alarms to sound. The QUICK FIND® feature
will immediately allow you to locate the
originating alarm (once the alarms have
stopped sounding). To initiate QUICK FIND®,
press the Test/Silence button on any alarm.
After releasing the button, the test sequence
will sound and then stop. Then, the originating
alarm will continue to sound for approx. 50
seconds. In a non-interconnected installation,
it is necessary to test each alarm to determine
the originating alarm. Reset the originating
alarm.
Horn has stopped
sounding
On and Blinks
Off approx.
every 20
seconds
Off and Blinks
On approx.
every 5
seconds until
reset
Off
Off
Condition: Latching smoke LED indicator.
The alarm has previously detected smoke
and had alarmed.
Recommendation: Follow the reset
instructions to remove the latching LED.
The alarm has previously detected smoke
and had alarmed.
Recommendation: Follow the reset
instructions to remove the latching LED.
Horn has stopped
sounding
On and Blinks
Off approx.
every 20
seconds
Off
Off
Off and Blinks
On approx.
every 5
seconds until
reset
Condition: Latching CO LED indicator. The
alarm has previously detected CO and had
alarmed.
Recommendation: Follow the reset
instructions to remove the latching LED.
alarm has previously detected CO and had
alarmed.
Recommendation: Follow the reset
instructions to remove the latching LED.