Recoton/Advent U31-LP2 用户手册
24
FPI U31-2 Gas Fireplace Insert
FAN MAINTENANCE
CAUTION: Label all wires prior
to disconnection when servicing
controls. Wiring error can cause
improper and dangerous opera-
to disconnection when servicing
controls. Wiring error can cause
improper and dangerous opera-
Remove the 2 screws holding the
grate in position.
Remove the 2 screws,
push Burner Tray to the left, and lift off.
Aeration Adjustment Rod
MAINTENANCE
If your fan requires maintenance or replacement,
access to the fan is through the plate on the
rear wall of the fi rebox. NOTE: the unit MUST
NOT be operated without the fan access
panel securely in place.
access to the fan is through the plate on the
rear wall of the fi rebox. NOTE: the unit MUST
NOT be operated without the fan access
panel securely in place.
10) Unplug the black wires from the fan motor
(from inside the stove).
11) Lift Fan Assembly off of the 2 pins, tip forward
and pull through fi rebox opening.
12) Disconnect green wire from power cord.
Replacing fan:
Reverse above steps. Hint for pushing fan down
onto pins - rub a bit of dish soap on the grommet
so it will slide more easily onto the pin. Check
to make sure the fan is seated properly on the
pins, this is very important- try to move the
fan back and forth, there should be no noise,
if there is check that the grommets haven't
come loose.
onto pins - rub a bit of dish soap on the grommet
so it will slide more easily onto the pin. Check
to make sure the fan is seated properly on the
pins, this is very important- try to move the
fan back and forth, there should be no noise,
if there is check that the grommets haven't
come loose.
When replacing the Burner Tray, slide the aera-
tion adjustment rod through the opening in the
front of the Valve Assembly.
tion adjustment rod through the opening in the
front of the Valve Assembly.
To remove fan:
1) Turn the unit off and allow it to cool to room
temperature.
2) Unplug or disconnect power source to
stove.
3) Remove glass front (see page 11).
4) Remove
logs.
5) Remove brick panels.
6) Remove the Grate by removing the screws
on each side of the grate.
7) Remove the Burner Tray by removing the
screws on each side of the tray. Push the
tray to the left and lift up.
tray to the left and lift up.
8) Remove the 11 screws holding the Access
Panel in place.
9) Remove the Fan Air Duct by removing 4
screws, 2 per side.
DOOR GLASS
REPLACEMENT
Your FPI insert is supplied with high temperature,
5 mm Neoceram ceramic glass that will withstand
the highest heat that your unit will produce. In
the event that you break your glass by impact,
purchase your replacement from an authorized
FPI dealer only, and follow our step-by-step
instructions for replacement.
5 mm Neoceram ceramic glass that will withstand
the highest heat that your unit will produce. In
the event that you break your glass by impact,
purchase your replacement from an authorized
FPI dealer only, and follow our step-by-step
instructions for replacement.
WARNING: do not operate appli-
ance with the glass front removed,
cracked or broken. Replacement
of the glass should be done by a
licensed or qualifi ed service per-
son.
ance with the glass front removed,
cracked or broken. Replacement
of the glass should be done by a
licensed or qualifi ed service per-
son.
Bay Glass Removal
1) Remove the door from the unit and place
on a soft surface to prevent scratching.
2) Remove the nuts holding the glass retainers
in place.
3) Remove the glass retainers (sides, top and
bottom).
4) Replace the glass. The glass must have
gasketing around it.
5) Reverse the previous steps, replace the
retainers and fasten with the nuts but do not
over tighten, as this can break the glass.
over tighten, as this can break the glass.
6) Replace door on the stove and check the
seal.
Flush Glass Replacement
Slide old glass out of the side frames and replace
with new glass.
with new glass.