Omron SYSMAC C200HW-ZW3AT2-E-V2 用户手册
5-3
Section
L: Data Link
63
Error Messages
The following table lists the error messages that are displayed on the check re-
sults screen. After confirming the check results, use “E: Edit table” to correct the
data link tables, then check the data link tables again.
sults screen. After confirming the check results, use “E: Edit table” to correct the
data link tables, then check the data link tables again.
Errors
Message
Meaning
Action
Insufficient Status
area
area
There are too few words in
the data area for the data link
status.
the data area for the data link
status.
Change the first status word
so that data link status (16
words) can be stored in the
area.
so that data link status (16
words) can be stored in the
area.
Table Data error
The first status word is
outside the allowable range.
(see note)
outside the allowable range.
(see note)
The link start word address of
area 1 is outside the
allowable range. (see note)
area 1 is outside the
allowable range. (see note)
The number of registered
nodes exceeds 62.
nodes exceeds 62.
The node address is 0 or
more than 62.
more than 62.
There is a node for which the
send area or receive area for
one node exceeds 1,000
words.
send area or receive area for
one node exceeds 1,000
words.
An offset exceeds 999.
An offset for the send area of
the local node is not 0.
the local node is not 0.
Correct the values within the
allowable range as shown in
the table on page 55.
allowable range as shown in
the table on page 55.
Duplicate Node
address
address
The same node address is
set more than once in the
data link table.
set more than once in the
data link table.
Correct the duplicate node
address.
address.
Link word number
over
over
There is a node for which the
total number of words in the
send areas of areas 1 and 2
exceeds 1,000.
total number of words in the
send areas of areas 1 and 2
exceeds 1,000.
Change the total number of
words in the send areas of
areas 1 and 2 to 1,000 or
less.
words in the send areas of
areas 1 and 2 to 1,000 or
less.
Too many words in
data link
data link
The total number of words in
the data link areas of areas 1
and 2 exceeds the maximum
allowable number of words for
the following PCs.
CS1-series PCs: 12,000
words
C200HX/HG/HE PCs: 8,000
words
CQM1H PCs: 8,000 words
CVM1 and CV-series PCs:
8,000 words
IBM PC/AT: 32,000 words
the data link areas of areas 1
and 2 exceeds the maximum
allowable number of words for
the following PCs.
CS1-series PCs: 12,000
words
C200HX/HG/HE PCs: 8,000
words
CQM1H PCs: 8,000 words
CVM1 and CV-series PCs:
8,000 words
IBM PC/AT: 32,000 words
Reduce the total number of
words in the data link areas of
areas 1 and 2 to the
maximum allowable number
of words for the following PCs
or less.
CS1-series PCs: 12,000
words
C200HX/HG/HE PCs: 8,000
words
CVM1 and CV-series PCs:
8,000 words
IBM PC/AT: 32,000 words
words in the data link areas of
areas 1 and 2 to the
maximum allowable number
of words for the following PCs
or less.
CS1-series PCs: 12,000
words
C200HX/HG/HE PCs: 8,000
words
CVM1 and CV-series PCs:
8,000 words
IBM PC/AT: 32,000 words
Link area overlap
error
error
The same data area is
specified for areas 1 and 2.
specified for areas 1 and 2.
The data link status words
overlap with a data link area.
overlap with a data link area.
Change the link start and first
status word of areas 1 and 2
so that the data link area and
the data link status words do
not overlap each other.
status word of areas 1 and 2
so that the data link area and
the data link status words do
not overlap each other.
Insufficient Link
area
(Area 1/ Area 2)
area
(Area 1/ Area 2)
There are not enough words
for the data link area.
for the data link area.
Correct the data link area
within the allowable range.
within the allowable range.
Link word number
0 error
0 error
The total number of link
words for one node is set to
0.
words for one node is set to
0.
Set the number of link words
for area 1 or 2.
for area 1 or 2.