BMW 2008 M3 Sedan 业主指南
Replacing components
124
4.
Adjust the tire inflation pressure to 29 psi/
200 kPa. With the ignition switched on, pro-
ceed as follows:
200 kPa. With the ignition switched on, pro-
ceed as follows:
>
To increase the inflation pressure:
Switch on the compressor, position I. To
check the current inflation pressure set-
ting, briefly switch off the compressor.
Switch on the compressor, position I. To
check the current inflation pressure set-
ting, briefly switch off the compressor.
Do not let the compressor run for
more than 10 minutes, otherwise the
more than 10 minutes, otherwise the
device will overheat and may be dam-
aged.
aged.
<
>
To reduce the inflation pressure: turn
screw
screw
8 on the pressure gauge.
If the inflation pressure is not maintained,
drive the vehicle a second time, refer to
drive the vehicle a second time, refer to
Distributing the sealant. Then repeat steps 1 to
4.
Use of the M Mobility System may be ineffec-
tual for tire damage larger than approx. 0.16 in/
4 mm. Please contact the nearest BMW center,
refer to page
4.
Use of the M Mobility System may be ineffec-
tual for tire damage larger than approx. 0.16 in/
4 mm. Please contact the nearest BMW center,
refer to page
, or a workshop that works
according to BMW repair procedures with cor-
respondingly trained personnel if the tire can-
not be made roadworthy with the M Mobility
System.
respondingly trained personnel if the tire can-
not be made roadworthy with the M Mobility
System.
<
The tire inflation pressure must be at least
29 psi/200 kPa. If it is not, do not continue
29 psi/200 kPa. If it is not, do not continue
driving.
<
Continuing your trip
Do not exceed the maximum allowable
speed of 50 mph/80 km/h to avoid the risk
speed of 50 mph/80 km/h to avoid the risk
of an accident.
<
Reinitialize the Flat Tire Monitor, refer to
page
page
for more information.
Have the faulty tire and the sealant bottle of the
M Mobility System replaced as soon as possi-
ble.
M Mobility System replaced as soon as possi-
ble.
<
Changing wheels
The tools for changing wheels are avail-
able as optional accessories from your
able as optional accessories from your
BMW center.
<
Jack mounting points
The jacking points are at the positions shown in
the illustration.
the illustration.
Vehicle battery
Battery care
The battery is 100% maintenance-free, the
electrolyte will last for the life of the battery
when the vehicle is operated in a temperate cli-
mate. Your BMW center will be glad to advise in
all matters concerning the battery.
electrolyte will last for the life of the battery
when the vehicle is operated in a temperate cli-
mate. Your BMW center will be glad to advise in
all matters concerning the battery.
Charging the battery
Only charge the battery in the vehicle via the
terminals in the engine compartment with the
engine off. Connections, refer to Jump starting
on page
terminals in the engine compartment with the
engine off. Connections, refer to Jump starting
on page
.
Disposal
Have old batteries disposed of by your
BMW center or hand them in to a recy-
BMW center or hand them in to a recy-
cling center. Maintain the battery in an upright
position for transport and storage. Always
secure the battery against tipping over during
transport.
position for transport and storage. Always
secure the battery against tipping over during
transport.
<
Power failure
After a temporary power loss, the functioning of
some equipment may be limited and require
reinitialization. Individual settings may likewise
have been lost and will have to be programmed:
some equipment may be limited and require
reinitialization. Individual settings may likewise
have been lost and will have to be programmed:
>
.
Online Edition for Part no. 01 41 0 014 956 - © 02/08 BMW AG