Whirlpool Washer 3LWTW4740YQ 用户手册

Operate your washer only when you are home. If moving, or 

not using your washer for a period of time, follow these steps:

1.  Unplug or disconnect power to washer.
2.  Turn off water supply to washer, to avoid flooding due  

to water pressure surge.

IMPORTANT: To avoid damage, install and store washer  

where it will not freeze. Because some water may stay in  

hoses, freezing can damage washer. If storing or moving  

during freezing weather, winterize your washer.
To winterize washer:

1.  Shut off both water faucets; disconnect and drain water     

inlet hoses.

2.  Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run 

washer on RINSE & SPIN cycle for about 30 seconds  

to mix antifreeze and remaining water.

3.  Unplug washer or disconnect power.

Replace inlet hoses after 5 years of use to reduce the risk of 

hose failure. Periodically inspect and replace inlet hoses if 

bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement 

on the label with a permanent marker.

1.   Always follow the detergent manufacturer’s instructions 

regarding the amount of detergent to use. Never use 

more than the recommended amount because that may 

increase the rate at which detergent and soil residue 

accumulate inside your washer, which in turn may result  

in undesirable odor.

2.    Use warm and hot wash water settings sometimes (not 

exclusively cold water washes), because they do a better 

job of controlling the rate at which soils and detergent 

accumulate.

3.    Always leave the washer lid open between uses to help 

dry out the washer and prevent the buildup of odor-

causing residue.

Read these instructions completely before beginning the 

routine cleaning processes recommended below. This 

Washer Maintenance Procedure should be performed, 

at a minimum, once per month or every 30 wash cycles, 

whichever occurs sooner, to control the rate at which soils 

and detergent may otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions 

provided above, and use this recommended monthly 

cleaning procedure:
Recommended Cycle for Cleaning the Washer
Refer to the “Cycle Guide” for the optimal cycle for cleaning 

the inside of the washer. Use this liquid chlorine bleach as 

described below.
Begin procedure
1.  Chlorine Bleach Procedure:
 

a.   Open the washer lid and remove any clothing  

or items.

 

b.   Add 236 mL (1 cup) of liquid chlorine bleach  

to the bleach compartment.

  

NOTE: Use of more liquid chlorine bleach than is  

    recommended above could cause washer damage  

  over 

time.

 

c.  Close the washer lid.

 

d.   Do not add any detergent or other chemical  

to the washer when following this procedure.

 

e.   Select the cycle recommended for cleaning the inside 

of the washer.

 

f.   Press the START/PAUSE/UNLOCK button to start the 

cycle.

  

NOTE: For best results, do not interrupt cycle. If cycle 

must be interrupted, press START/PAUSE/UNLOCK 

once or twice [depending on model]. After the cycle has 

stopped, run a RINSE and SPIN cycle to rinse cleaner 

from washer.

Cleaning the Dispensers
After a period of using your washer, you may find some 

residue buildup in the washer’s dispensers. To remove 

residue from the dispensers, wipe them with a damp cloth 

and towel dry. Do not attempt to remove the dispensers or 

trim for cleaning. The dispensers and trim are not removable. 

If your model has a dispenser drawer, however, remove the 

drawer and clean it before or after you run the Clean Washer 

cycle. Use an all-purpose surface cleaner, if needed.

Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.  

Use only mild soaps or cleaners when cleaning external 

washer surfaces.

IMPORTANT: To avoid damaging the washer’s finish, do not 

use abrasive products.