Husqvarna Portable Generator PP 418 用户手册
9
ASSEMBLY
NOTICE
The PP 418 power pack must be serviced before use.
In some markets the power pack will be delivered
fi lled with both engine oil and hydraulic oil.
fi lled with both engine oil and hydraulic oil.
Remove the power pack from its shipping material and place it
on a level surface.
on a level surface.
Step 1
Check the engine oil level. If no oil is present on the dipstick
add oil in accordance to the recommendations on page 8 or
consult the BRIGGS & STRATTON Operator’s Manual.
Check the engine oil level. If no oil is present on the dipstick
add oil in accordance to the recommendations on page 8 or
consult the BRIGGS & STRATTON Operator’s Manual.
CAUTION
Only use the lifting eyelet when lifting the power pack.
Dipstick
Oil
Fill
Full
SAE 30
Step 2
Fill the hydraulic oil tank.
Use only a high quality hydraulic oil – ISO 46. See page 8
for other alternatives. The total fi rst time oil amount needed is
10 liters (2.6 gal) to fi ll the tank. The oil should be fi lled to the
middle of the sight glass.
Fill the hydraulic oil tank.
Use only a high quality hydraulic oil – ISO 46. See page 8
for other alternatives. The total fi rst time oil amount needed is
10 liters (2.6 gal) to fi ll the tank. The oil should be fi lled to the
middle of the sight glass.
The oil level must be rechecked and refi lled after the initial test
running has been done - see page 12.
running has been done - see page 12.
Step 3
Hook up the hydraulic hoses to the power pack. Connect the
two couplers in the free end of the hose. The hoses are now
ready to be charged with oil from the oil tank.
Hook up the hydraulic hoses to the power pack. Connect the
two couplers in the free end of the hose. The hoses are now
ready to be charged with oil from the oil tank.
NOTE:
The hoses can be installed with either end to the power pack.
Any set of hoses assembled with the couplers as in this
illustration will always have full compatibility between power
pack, hoses and tool.
The hoses can be installed with either end to the power pack.
Any set of hoses assembled with the couplers as in this
illustration will always have full compatibility between power
pack, hoses and tool.
P
O
W
E
R
P
A
C
K
M
A
N
I
F
O
L
D
Female
Male
Male
Female
Step 5
The power pack is delivered without the battery cables
installed to the battery. Please read;
SERVICING THE BATTERY on page 10.
The original equipment battery is maintenance free. Do not
attempt to open or remove caps or covers. Adding or checking
the level of electrolyte is not necessary.
The power pack is delivered without the battery cables
installed to the battery. Please read;
SERVICING THE BATTERY on page 10.
The original equipment battery is maintenance free. Do not
attempt to open or remove caps or covers. Adding or checking
the level of electrolyte is not necessary.
WARNING
Lead-acid batteries generate explosive gases.
Keep sparks, fl ame and smoking materials away from
batteries. Always wear eye protection when around
batteries.
Keep sparks, fl ame and smoking materials away from
batteries. Always wear eye protection when around
batteries.
Step 4
Check the tire pressure. The wheels are tubeless. If the tire
pressure becomes too low the wheel will defl ate completely.
Infl ate to 2 bar (30 psi)
Check the tire pressure. The wheels are tubeless. If the tire
pressure becomes too low the wheel will defl ate completely.
Infl ate to 2 bar (30 psi)
If the hydraulic hoses (7.5 m/25 ft) are empty they will require
approximately 1.8 liters (2 quarts) of additional oil to be added
to the oil tank after running the power pack for the fi rst time.
approximately 1.8 liters (2 quarts) of additional oil to be added
to the oil tank after running the power pack for the fi rst time.
If an additional 30 m (100 ft) of 5/8” hose set is used they will
require approximately 12 liters (3.2 gal) to be added. The oil
level in the oil tank must be rechecked several times when
fi lling a new hose set.
require approximately 12 liters (3.2 gal) to be added. The oil
level in the oil tank must be rechecked several times when
fi lling a new hose set.
Step 6
Fill the fuel tank with fresh clean gasoline. See warnings and
recommendations on page 8. Add only fuel in a quantity that
will be used within 30 days to assure fuel freshness. If the
power pack is stored with fuel in the tank for longer periods we
recommend to use a commercially available “Fuel Stabilizer”.
Fill the fuel tank with fresh clean gasoline. See warnings and
recommendations on page 8. Add only fuel in a quantity that
will be used within 30 days to assure fuel freshness. If the
power pack is stored with fuel in the tank for longer periods we
recommend to use a commercially available “Fuel Stabilizer”.