Amana PTH094G35AXXX 目录

Product Specifications: PTH Models — Reverse-Cycle Heating Performance

Voltage ¹

,

 ³

230 / 208

230 / 208

230 / 208

230 / 208

265

265

265

265

BTU/h ⁵

6,800 / 6800

8,300 / 8,100

11,500 / 11,300

13,800 / 13,600

6,800

8,300

11,400

13,700

Amps ¹⁰

3.9 / 3.9

4.2 / 4.2

5.8 / 5.8

7.0 / 7.0

3.1

3.7

5.0

6.1

Watts ¹⁰

585 / 585

715 / 700

1085 /1035

1350 / 1330

585

715

1080

1340

COP ⁵

3.4 / 3.4

3.4 /3.4

3.1 / 3.2

3.0 / 3.0

3.4

3.4

3.1

3.0

CFM (Dry)

370

360

370

410

370

360

370

410

COP = Coefficiency of Performance; per AHRI Test Procedures, units are rated for capacities and efficiencies.

¹  All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).

²  Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.

³  Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.  

Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.

⁴  Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must  

be cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).

⁵  Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric  

heat at approximately 24°F outdoor ambient.

⁶  Specify two-digit heater kW size to complete model number.

⁷  R-410A refrigerant used in all systems.

⁸  All units meet or exceed ASHRAE 90.1 standards.

⁹  All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.

¹⁰  Refer to electric heat performance data for total MCA and recommended overcurrent protection.  

Amps and Watts notation refers to compressor only.

Product Specifications: PTC / PTH Models — Electric Heat Performance

(Primary Heating for PTC Models; Auxiliary Heating for PTH Models; See below for Power Cord Configuration)

230/208V

1.5 / 1.3

1

5,100

4,200

- -

1,570 / 1,295

6.8 / 6.2

8.5

15

6-15 P

230/208V

2.5 / 2.1

1

8,500

6,800

- -

2,570 / 2,115

11.2 / 10.1

14.1

15

6-15 P

230/208V

3.5 / 3.0

1

12,000

9,900

- -

3,570 / 2,935

15.5 / 14.1

19.5

20

6-20 P

230/208V

5.0 / 4.1

1

17,100

14,000

- -

5,070 / 4,160

22.1 / 20.0

27.6

30

6-30 P

265V

1.5

1

- -

- -

5,100

1,570

5.9

7.4

15

7-20P

265V

2.5

1

- -

- -

8,500

2,570

9.7

12.2

15

7-20 P

265V

3.7

1

- -

- -

12,600

3,770

14.2

17.9

20

7-20 P

265V

5

1

- -

- -

17,100

5,070

19.2

23.9

25

7-30 P

¹  All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).

²  Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.

³  Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts. Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.

⁴  Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style  

time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).

⁵  Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric heat at  

approximately 24°F outdoor ambient.

⁶  Total watts for 15,000 BTU/h models; subtract 20 watts for PT07/09/12

⁷  Specify two-digit heater kW size to complete model number.

⁸  R-410A refrigerant used in all systems.

⁹  All units meet or exceed ASHRAE 90.1 standards.

¹⁰  All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.