Frigidaire FGIC3067MB 使用和维护

9

Be sure that your fi nger is placed in the center of the touch 

pad. If the fi nger is not placed on the center of a pad, the 

cooktop may not respond to the selection made.

Lightly contact the pad with the fl at part of your entire fi ngertip. 

Do not just use the narrow end of your fi ngertip.

This feature allows the cooktop to be locked only when the 

cooktop is switched to OFF. Touch and hold the LOCK key 

pad for 3 seconds. A beep will sound and the Lock LED will 

glow (Fig. 11). Once locked, no other displays will glow and 

no Cooking Zones will activate. To turn the Controls Lock 

OFF, touch and hold the LOCK key pad for 3 seconds. A 

beep will sound, the Lock LED will turn OFF (Fig. 10) and 

the cooktop may be used normally.

Each of the Cooking Zones have separate ON/OFF key 

pads. Once the Main Power key pad has been touched to 

activate the cooktop, touch the corresponding Cooking 

Zone ON/OFF key pad once to activate the Cooking Zone 

needed. “-” will appear in the display and the ON/OFF LED 

will glow (Fig. 6). If the corresponding UP/DOWN Arrow 

key pad is not touched within 10 seconds, the request to 

turn the Cooking Zone ON will cancel and the Cooktop will 

go back to ready mode. To turn OFF a Cooking Zone, touch 

the Cooking Zone ON/OFF key pad once. The Cooking Zone 

LED will turn OFF (Fig. 5).

The Cooking Zones have separate Power Level displays. 

Once active, the Cooking Zones will provide 15 Power Levels 

to choose from. These include 1 (Fig. 7), 2, 2., 3, 3., 4, 4., 

5, 5., 6, 6. (Fig. 8), 7, 8, 9, p. Half power levels (available 

between 2 and 7 power level) are indicated by lighting the 

display decimal point (Fig. 8). The highest setting of P or 

“Power Boost” provides approximately 139% power for 10 

minutes (Fig. 9). After 10 minutes, the power level drops 

to 9. Each key pad touch (or just holding down the Power 

Level key pad) will scroll through all the available power 

levels for any Cooking Zone quickly.

Fig. 1

Fig. 5

Fig. 10

Fig. 7

Fig. 3

Fig. 8

Fig. 9

Fig. 2

Fig. 6

Fig. 11

Once any Cooking Zone has been used for cooking and 

turned OFF, and if the cooktop surface temperature on 

any of the Cooking Zones is still too HOT, “H” (Fig. 3) will 

appear in the display for the affected Cooking Zone. The H 

will continue to display if the temperature is still too HOT.

 The Cooking Zones may appear 

to be cool while turned ON and after they have 

been turned OFF. But the glass surface may 

be HOT from residual heat transferred from 

the cookware and burns may occur if surface 

is touched.

The Cooktop POWER key pad activates the entire Cooktop. 

To power the cooktop, touch and hold the POWER key pad 

for 2 seconds. A beep will sound and the Power LED will glow 

(Fig. 2). The cooktop will be in a ready mode for 10 seconds. 

If no other key pads are touched the Cooktop Main POWER 

will turn OFF automatically. To turn the Main Power OFF touch 

and hold the Main POWER key pad for 1 second. A beep will 

sound and the Power LED will turn OFF (Fig. 1).

Fig. 4

Use the Keep Warm key pad to activate the 

Warm setting for any of the Cooking Zones. 

The ON/OFF key pad for the desired Cooking 

Zone must be activated fi rst, then touch the 

Keep Warm key pad located in the Cooktop 

Main Control area once to set. “L” (low heat) 

should appear in the corresponding Cooking 

Zone display (Fig. 4).

All Cooking Zones will provide a Pan Detection message. 

If a Cooking Zone is turned ON and no pan is detected, or 

the pan has been moved or is not centered correctly, or is 

not made of magnetic material, the power level will fl ash 

in the affected Cooking Zone display. If the situation is not 

corrected, the zone will turn off after 3 minutes.