Omega VRT400 用户手册
22
23
TROUBLESHOOTING
APPLIANCE SPECIFICATIONS
Check the details below before contacting Technical Support for repair or service.
If you need information or if you have a problem, please contact the local Customer Care Center.
When applying for after sales service, check the manufacturer’s serial number or bar code.
If you need information or if you have a problem, please contact the local Customer Care Center.
When applying for after sales service, check the manufacturer’s serial number or bar code.
THE APPLIANCE DOES NOT WORK.
Make sure the power cord is properly plugged in.
Check the hopper is assembled properly. If the hopper has not been properly locked in place, the appliance does not work for safety reasons.
Check if the appliance has been assembled according to the manual in an ordinary manner.
See the assembly in the manual or consult with the local Customer Care Center for help.
Check the hopper is assembled properly. If the hopper has not been properly locked in place, the appliance does not work for safety reasons.
Check if the appliance has been assembled according to the manual in an ordinary manner.
See the assembly in the manual or consult with the local Customer Care Center for help.
THE HOPPER DOES NOT OPEN.
Is there alot of pulp left inside the bowl? Press [ ON ] button to discharge internal pulp.
Have you placed any foreign substances or solid objects such as hard seeds?
Press the [ Reverse/REV ] button to make foreign substances come up again toward the feeding tube.
Do not attempt to open it by force or with too much pressure. Still it does not work following by the above process,
Have you placed any foreign substances or solid objects such as hard seeds?
Press the [ Reverse/REV ] button to make foreign substances come up again toward the feeding tube.
Do not attempt to open it by force or with too much pressure. Still it does not work following by the above process,
contact the local Customer Care Center.
IT STOPS DURING NORMAL OPERATION.
Have you put heavy loads of ingredient or a thick/big ingredient? Read the manual Page 12 and follow Reverse/REV button guideline
Still the problem has not been solved, contact the local Customer Care Center.
Still the problem has not been solved, contact the local Customer Care Center.
THERE ARE GATE MARKS (FORMING MARK) RESULTING FROM THE MOLDING PROCESS.
It is normal, and there is no problem for use.
WHAT IS THE DIFFERENCE BETWEEN FINE STRAINER AND COARSE STRAINER?
Regarding strainer selection for suitable ingredients, read the manual Page 3.
JUICE LEAKS OVER THE BASE.
Is Extraction packing properly inserted in?
Juice could leak when the extraction packing is not properly inserted. Please push the extraction packing tight enough.
Juice is still leaking even though the extraction packing was inserted properly?
If an amount of input ingredient is too much compared to the size of pulp outlet, the packing may be slightly pushed out and
Juice could leak when the extraction packing is not properly inserted. Please push the extraction packing tight enough.
Juice is still leaking even though the extraction packing was inserted properly?
If an amount of input ingredient is too much compared to the size of pulp outlet, the packing may be slightly pushed out and
juice may leak through the gap. Do not process heavy loads at a time; squeeze little by little.
THE BOWL SHAKES WHEN SQUEEZING.
Slight shaking may be occurred due to motor movement.
Large or small movements occur depending on the pulp texture of ingredients (hard or tough).
It is normal when the screw is rotating. Please note that it is not malfunction.
Hard ingredients (e.g:carrots/potatoes/radishes/beetroots etc.) may shake the bowl more than soft and juicy ingredient.
Large or small movements occur depending on the pulp texture of ingredients (hard or tough).
It is normal when the screw is rotating. Please note that it is not malfunction.
Hard ingredients (e.g:carrots/potatoes/radishes/beetroots etc.) may shake the bowl more than soft and juicy ingredient.
APPLIANCE STANDARDS
PRODUCT NAME Omega Slow Squeeze Juicer
MODEL NAME
VR T400 Series
RATED VOLTAGE
120 V
RATED FREQUENCY 60 Hz
RATED POWER
CONSUMPTION
150 W
RPM (REVOLUTIONS
PER MINUTE)
80 RPM
CORD LENGTH
1.4 m
MOTOR
Single-phase
induction motor
FUSE
250 V 10 A
OUT WARD
Width 160 MM
DIMENSIONS
Length 218 mm
Height 405 mm
RATED
OPERATING TIME
LESS THAN 30 MINUTES