Traulsen Quality Refrigeration 用户手册
TABLE OF CONTENTS
The serial tag is a permanently affixed sticker on
which is recorded vital electrical and refrigeration data
about your Traulsen product, as well as the model
and serial number. This tag is located in the upper
right interior compartment on all reach-in/pass-thru
and roll-in/roll-thru refrigerator, freezer and dual-temp
models. For hot food and proofer models, this tag is
located on the top of the unit behind the louvers to
protect it from the heat.
which is recorded vital electrical and refrigeration data
about your Traulsen product, as well as the model
and serial number. This tag is located in the upper
right interior compartment on all reach-in/pass-thru
and roll-in/roll-thru refrigerator, freezer and dual-temp
models. For hot food and proofer models, this tag is
located on the top of the unit behind the louvers to
protect it from the heat.
I. THE SERIAL TAG
-1-
FORT WORTH, TX.
SERIAL
MODEL
VOLTS
Hz
PH
TOTAL CURRENT
AMPS
MINIMUM CIRCUIT
AMPS
MAXIMUM OVERCURRENT PROTECTION
AMPS
LIGHTS
WATTS
HEATERS
AMPS
REFRIGERANT
TYPE
OZ
DESIGN PRESSURE
HIGH
LOW
REFRIGERANT
TYPE
OZ
DESIGN PRESSURE
HIGH
LOW
370-60294-00 REV (A)
READING THE SERIAL TAG
• Serial = The permanent ID# of your Traulsen
• Model = The model # of your Traulsen
• Volts = Voltage
• Hz = Cycle
• PH = Phase
• Total Current = Maximum amp draw
• Minimum Circuit = Minimum circuit ampacity
• Lights = Light wattage
• Heaters = Heater amperage (Hot Food units only)
• Refrigerant = Refrigerant type used
• Design Pressure = High & low side operating
pressures and refrigerant charge
• Agency Labels = Designates agency listings
• Model = The model # of your Traulsen
• Volts = Voltage
• Hz = Cycle
• PH = Phase
• Total Current = Maximum amp draw
• Minimum Circuit = Minimum circuit ampacity
• Lights = Light wattage
• Heaters = Heater amperage (Hot Food units only)
• Refrigerant = Refrigerant type used
• Design Pressure = High & low side operating
pressures and refrigerant charge
• Agency Labels = Designates agency listings
VII. PROOFER & PROOFER/RETARDER MODELS
a-Installation
Page 6
b-Proofer Operating Instructions
Page 6
c-Operating The Dial Humidistat
Page 6-7
d-Retarder Operation
Page 7-8
e- Care of Water Tank & Heating Elements
Page 8
f-Interior Arrangements
Page 8
VIII. EVEN-THAW MODELS
a-Application Overview
Page 9
b-Product Loading Guidelines
Page 9
c-Starting An Even-Thaw Cycle
Page 9
d-Conclusion Of Even-Thaw Cycle
Page 9
e-Interior Arrangements
Page 9
f-Frequently Asked Questions
Page 9-10
IX. FISH FILE MODELS
a-Fish File Application
Page 10
b-Special Installation Note
Page 10
c-Drawer Pans
Page 10
d-Product Loading
Page 10
e-Cleaning
Page 10
X. BLAST FREEZER MODELS
a-Blast Freezer Application
Page 11
b-Special Installation Note
Page 11
c-Interior Arrangements
Page 11
d-Blast Freezing vs. Blast Chilling
Page 11
e-Normal Operation
Page 11
f-Defrost
Page 11
g-Blast Chill Operation
Page 11
h-Proper Packaging
Page 11
XI. TROUBLE SHOOTING GUIDE
Page 12
XII. WARRANTY INFORMATION
Page 13
XIII. INDEX
Page 14
I. THE SERIAL TAG
Page 1
II. RECEIPT INSPECTION
Page 2
III. INSTALLATION
a-Location
Page 2
b-Packaging
Page 2
c-Installing Legs or Casters
Page 2
d-Shelf Pins
Page 2
e-Roll-In Model Installation
Page 3
f-Installing The Condensate Evaporator
Page 3
g-Remote Installation
Page 3
h-Cord & Plug
Page 3
i-Power Supply
Page 4
j-Wiring Diagram
Page 4
k-Compressor Hold Down Provisions
Page 4
l-Clearance
Page 4
IV. CARE & MAINTENANCE
a-Cleaning The Condenser
Page 4
b-Hinge Replacement
Page 4-5
c-Replacing The Gaskets
Page 5
d-Cleaning The Exterior
Page 5
e-Cleaning The Interior
Page 5
V. MISC. OPERATIONS
a-Adjusting The Shelves
Page 5
VI. OTHER
a-Service Information
Page 5
b-Spare Parts
Page 5
c-Warranty Registration
Page 5