Sanyo DSR-3506P 用户手册
INSTALLATION AND CONNECTIONS
3
English
11
The sensor alarm output terminals are used to relay alarm
signals whenever one of the digital video recorder’s motion
sensors is triggered. Normally in an open condition, a
terminal adopts low condition when a sensor for the
corresponding camera number has been triggered.
signals whenever one of the digital video recorder’s motion
sensors is triggered. Normally in an open condition, a
terminal adopts low condition when a sensor for the
corresponding camera number has been triggered.
The connections for a remote control circuit are shown
below. This digital video recorder can be remotely controlled
when a remote-control circuit similar to that shown here is
connected to the remote-input control terminals.
below. This digital video recorder can be remotely controlled
when a remote-control circuit similar to that shown here is
connected to the remote-input control terminals.
z
Use a resistance of 1/10 ohms or more and with a D
ranking (Precision within ±0.5%).
ranking (Precision within ±0.5%).
z
The remote control cable should be no more than 5m
long.
long.
1
When you have finished making all the
other connections, make sure the
voltage is 120V-240V AC and insert the
power plug into the wall outlet.
other connections, make sure the
voltage is 120V-240V AC and insert the
power plug into the wall outlet.
There is no power switch. The display indicators flash, and
after a few moments, the monitor screen displays the
camera image.
after a few moments, the monitor screen displays the
camera image.
z
When turning the power ON for the first time
“PLEASE SET THE CLOCK” is displayed on the
monitor screen. Follow the procedures on P.14 to set
the clock.
“PLEASE SET THE CLOCK” is displayed on the
monitor screen. Follow the procedures on P.14 to set
the clock.
z
If the clock is already set
The operation display area is displayed.
The operation display area is displayed.
z
If the POWER indicator starts flashing;
The POWER indicator flashes when there is a problem
with the hard disk. In this type of situation, initialize the
hard disk. (JP.81)
If you need to save video stored on the disk, contact the
dealer from whom you purchased this digital video
recorder.
The POWER indicator flashes when there is a problem
with the hard disk. In this type of situation, initialize the
hard disk. (JP.81)
If you need to save video stored on the disk, contact the
dealer from whom you purchased this digital video
recorder.
z
The power cord’s ground terminal is not provided for
enhanced safety; rather, it can be used to reduce the
level of interference when the digital video recorder is
connected to analog devices.
If a large amount of noise is generated when the digital
video recorder is connected to analog devices, connect
this terminal to the building’s earth.
enhanced safety; rather, it can be used to reduce the
level of interference when the digital video recorder is
connected to analog devices.
If a large amount of noise is generated when the digital
video recorder is connected to analog devices, connect
this terminal to the building’s earth.
Connecting SENSOR ALARM OUT
terminals
terminals
Connecting control terminals
1K
Rating for each terminal
z
z
Maximum current: 25 mA
z
Maximum voltage: 25 V
R1
C
R2
SW 1
SW 2
SW 3
SW 4
SW 5
SW 6
SW 7
SW 8
SW 9
SW 10
SW 11
SW 12
SW 13
SW 14
SW 15
SW 16
SW 2
SW 3
SW 4
SW 5
SW 6
SW 7
SW 8
SW 9
SW 10
SW 11
SW 12
SW 13
SW 14
SW 15
SW 16
SW 17
SW 18
SW 19
SW 20
SW 21
SW 22
SW 23
SW 24
SW 25
SW 26
SW 27
SW 28
SW 29
SW 30
SW 31
SW 32
SW 18
SW 19
SW 20
SW 21
SW 22
SW 23
SW 24
SW 25
SW 26
SW 27
SW 28
SW 29
SW 30
SW 31
SW 32
R1
R2
: Camera 1*: Not used
: Camera 2*: Not used
: Camera 3*: Not used
: Camera 4*: SEQUENCE
: Camera 5*: MON2
: Camera 6*: OSD
: Not used: QUAD
: Not used: MULTI
: Not used: MENU RESET
: Not used: Not used
: Not used: Not used
: Not used: Not used
: Not used: Not used
: Not used: Not used
: Not used: Not used
: Not used: Not used
: REC/STOP
: PLAY/STOP
: STILL
: SEARCH
: SHIFT (Doubles with R1)
: PLAY
: REC
: MENU
: EXIT
: +
: -
:
→
:
←
: ZOOM
: COPY
: TIMER
(When combined
with R2 Shift key)
(When operated
independently)
Connecting the power cord
120V-240V AC
(50/60 Hz)
(50/60 Hz)
02
0
01-01-04 00:00:00 REC REPEAT EN A ALARM 0000
Operation
display area
e00_l8hbe_xe_7.book Page 11 Tuesday, April 27, 2004 10:35 AM